- 您現在的位置：買賣IC網 > PDF目錄1983 > AD7739BRU (Analog Devices Inc)IC ADC 24BIT 8-CH 24-TSSOP PDF資料下載
參數資料
| 型號： | AD7739BRU |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 13/32頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 24BIT 8-CH 24-TSSOP |
| 標準包裝： | 1 |
| 位數： | 24 |
| 采樣率（每秒）： | 15.1k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 100mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 24-TSSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 8 個單端，單極；8 個單端，雙極；4 個差分，單極；4 個差分，雙極 |
| 配用： | EVAL-AD7739EBZ-ND - BOARD EVAL FOR AD7739 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7739
Data Sheet
Rev. A | Page 20 of 32
Bit
Mnemonic
Description
4
CLKDIS
Master clock output disable. When this bit is set to 1, the master clock is disabled from appearing at the
MCLKOUT pin and the MCLKOUT pin is in a high impedance state. This allows turning off the MCLKOUT as a
power saving feature. When using an external clock on MCLKIN, the AD7739 continues to have internal clocks
and converts normally regardless of the CLKDIS bit state. When using a crystal oscillator or ceramic resonator
across the MCLKIN and MCLKOUT pins, the AD7739 clock is stopped and no conversions can take place when the
CLKDIS bit is active. The AD7739 digital interface can still be accessed using the SCLK pin.
3
Dump
Dump mode. When this bit is reset to 0, the channel status register and channel data register are addressed and
read separately. When the dump bit is set to 1, the channel status register is followed immediately by a read of
the channel data register regardless of whether the status or data register has been addressed through the
communications register. The continuous read mode is always dump mode reading the channel status and
channel data registers, regardless of the dump bit value (see the Digital Interface Description section for details).
2
Cont RD
When this bit is set to 1, the AD7739 operates in the continuous read mode (see the Digital Interface Description
section for details).
1
24/16 bit
Channel data register data width selection bit. When set to 1, the channel data registers are 24 bits wide. When
set to 0, the channel data registers is 16 bits wide.
0
Clamp
This bit determines the value of the channel data register when the analog input voltage is outside the nominal
input voltage range. When the clamp bit is set to 1, the channel data register is digitally clamped to either all 0s
or all 1s when the analog input voltage goes outside the nominal input voltage range. When the clamp bit is
reset to 0, the data registers reflect the analog input voltage even outside the nominal voltage range (see the
Table 29. Mode Settings
MD2 MD1 MD0 Operating Mode Description
0
Idle
The default mode after power-on or reset. The AD7739 automatically returns to this mode after any
calibration or after a single conversion.
0
1
Continuous
conversion
The AD7739 performs a conversion on the specified channel. After the conversion is complete, the
relevant channel data register and channel status register are updated, the relevant RDY bit in the
ADC status register is set, and the AD7739 continues converting on the next enabled channel. The
part cycles through all enabled channels until it is put into another mode or reset. The cycle period is
the sum of all enabled channels’ conversion times, set by the corresponding channel conversion time
registers.
0
1
0
Single
conversion
The AD7739 performs a conversion on the specified channel. After the conversion is complete, the
relevant channel data register and channel status register are updated, the relevant RDY bit in the
ADC status register is set, the RDY pin goes low, the MD2 to MD0 bits are reset, and the AD7739
returns to idle mode. Requesting a single conversion ignores the channel setup register enable bits; a
conversion is performed even if that channel is disabled.
0
1
Power-down
(standby)
The ADC and the analog front end (internal buffer) go into the power-down mode. The AD7739
digital interface can still be accessed. The CLKDIS bit works separately, and the MCLKOUT mode is not
affected by the power-down (standby) mode.
1
0
ADC zero-scale
self-calibration
A zero-scale self-calibration is performed on internally shorted ADC inputs. After the calibration is
complete, the contents of the ADC zero-scale calibration register are updated, all RDY bits in the ADC
status register are set, the RDY pin goes low, the MD2 to MD0 bits are reset, and the AD7739 returns
to idle mode.
1
0
1
ADC full-scale
self-calibration
A full-scale self-calibration is performed on an internally generated full-scale signal. After the
calibration is complete, the contents of the ADC full-scale calibration register are updated, all RDY bits
in the ADC status register are set, the RDY pin goes low, the MD2 to MD0 bits are reset, and the
AD7739 returns to idle mode.
1
0
Channel zero-
scale system
calibration
A zero-scale system calibration is performed on the selected channel. An external system zero-scale
voltage must be provided at the AD7739 analog input and this voltage must remain stable for the
duration of the calibration. After the calibration is complete, the contents of the corresponding
channel zero-scale calibration register are updated, all RDY bits in the ADC status register are set,
the RDY pin goes low, the MD2 to MD0 bits are reset, and the AD7739 returns to idle mode.
1
Channel full-
scale system
calibration
A full-scale system calibration is performed on the selected channel. An external system full-scale
voltage must be provided at the AD7739 analog input and this voltage must remain stable for the
duration of the calibration. After the calibration is complete, the contents of the corresponding
channel full-scale calibration register are updated, all RDY bits in the ADC status register are set,
the RDY pin goes low, the MD2 to MD0 bits are reset, and the AD7739 returns to idle mode.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7760BSVZ-REEL | IC ADC 24BIT 2.5MSPS 64TQFP |
| AD7762BSVZ-REEL | IC ADC 24BIT 625KSPS 64TQFP |
| AD7763BSVZ | IC ADC 24BIT SRL 625KSPS 64TQFP |
| AD7764BRUZ-REEL7 | IC ADC 24BIT S/D 312KSPS 28TSSOP |
| AD7765BRUZ-REEL7 | IC ADC 24BIT S/D 156KSPS 28TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7739BRU-REEL | 功能描述:IC ADC 24BIT 8CH SIG-DEL 24TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7739BRU-REEL7 | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 3.05Msps 24-bit Serial 24-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 15.133KSPS 24BIT SERL 24TSSOP - Tape and Reel |
| AD7739BRUZ | 功能描述:IC ADC 24BIT 8-CH 24-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD7739BRUZ | 制造商:Analog Devices 功能描述:IC, ADC, 24BIT, 15.1KSPS, TSSOP-24 |
| AD7739BRUZ-REEL7 | 功能描述:IC ADC 24BIT 8CH SIG-DEL 24TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。