- 您現在的位置：買賣IC網 > PDF目錄10243 > AD7738BRUZ-REEL7 (Analog Devices Inc)IC ADC 24BIT 8CH SIG-DEL 28TSSOP PDF資料下載
參數資料
| 型號： | AD7738BRUZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 20/28頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 24BIT 8CH SIG-DEL 28TSSOP |
| 標準包裝： | 1,000 |
| 位數： | 24 |
| 采樣率（每秒）： | 15.4k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 100mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 28-TSSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 8 個單端，單極；8 個單端，雙極；4 個差分，單極；4 個差分，雙極 |
| 配用： | EVAL-AD7738EBZ-ND - BOARD EVAL FOR AD7738 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
REV. 0
AD7738
–27–
CALIBRATION
The AD7738 provides zero-scale self-calibration, and zero and
full system calibration capability, which can effectively reduce
the offset error and gain error to the order of the noise. After
each conversion, the ADC conversion result is scaled using the
ADC Calibration Registers and the relevant Channel Calibration
registers before being written to the Data register. See the equa-
tions shown below.
For unipolar ranges:
Data = ((ADC result – ADC ZS Cal. reg.)
ADC FS reg./
200000h – Ch. ZS Cal. reg.)
Ch. FS Cal. reg./200000h
For bipolar ranges:
Data = ((ADC result – ADC ZS Cal. reg.)
ADC FS reg./
400000h + 800000h – Ch. ZS Cal. reg.)
Ch. FS Cal. reg./
200000h
Where the ADC result is in the range of 0 to FFFFFFh.
Note that the Channel ZS Calibration register has the format of
a sign bit + 22 bits Channel offset value.
It is strongly recommended that the user does not change the
ADC FS register.
To start any calibration, write the relevant mode bits to the
AD7738 Mode register. After the calibration is complete, the
contents of the corresponding Calibration registers are updated, all
RDY bits in the ADC Status register are set, the
RDY pin goes
low, and the AD7738 reverts to Idle mode.
The calibration duration is the same as conversion time configured
on the selected channel. The longer conversion time gives less
noise and yields a more exact calibration. Therefore, use at least
the default conversion time to initiate any calibration.
ADC Zero-Scale Self-Calibration
The ADC Zero-Scale Self-Calibration can effectively remove
the offset error in Chopping Disabled mode. If repeated after a
temperature change, it can also remove the offset drift error in
Chopping Disabled mode.
The zero-scale self-calibration is performed on internally shorted
ADC inputs. The negative Analog Input terminal on the selected
channel is used to set the ADC ZS Calibration common mode.
Therefore, either the negative terminal on selected differential pair
or AINCOM on single-ended channel configuration should be
driven to a proper commwon-mode voltage.
It is strongly recommended that the ADC ZS Calibration register
should only be updated as part of a zero-scale self-calibration.
Per Channel System Calibration
If the per channel system calibrations are used, these should be
initiated in the following order: first a Channel ZS System Cali-
bration followed by a Channel FS System Calibration.
The System Calibration is affected by the ADC ZS and FS Cali-
bration registers; therefore, if both Self-Calibration and System
Calibration are used in a system, an ADC Self-Calibration cycle
should be performed first followed by a System Calibration cycle.
While executing a system calibration, the fully settled system
zero-scale voltage signal or system full-scale voltage signal must
be connected to the selected channel analog inputs.
The per channel Calibration registers can be read, stored, or
modified and written back to the AD7738. Note, when writing
the Calibration registers the AD7738 must be in the idle mode.
Note that outside the specified calibration range, the calibration
is possible but the performance may degrade. (See the System
Calibration section in the specification pages of this data sheet.)
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B2L-MW-F4 | CONVERTER MOD DC/DC 28V 100W |
| VE-23R-CU-F3 | CONVERTER MOD DC/DC 7.5V 200W |
| VI-26D-MY | CONVERTER MOD DC/DC 85V 50W |
| VE-B2L-MW-F3 | CONVERTER MOD DC/DC 28V 100W |
| AD7738BRUZ-REEL | IC ADC 24BIT 8CH SIG-DEL 28TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7739 | 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Channel, High Throughput, 24-Bit Sigma-Delta ADC |
| AD7739BRU | 功能描述:IC ADC 24BIT 8-CH 24-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7739BRU-REEL | 功能描述:IC ADC 24BIT 8CH SIG-DEL 24TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7739BRU-REEL7 | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 3.05Msps 24-bit Serial 24-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 15.133KSPS 24BIT SERL 24TSSOP - Tape and Reel |
| AD7739BRUZ | 功能描述:IC ADC 24BIT 8-CH 24-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
發布緊急采購，3分鐘左右您將得到回復。