- 您現在的位置：買賣IC網 > PDF目錄1983 > AD7722ASZ (Analog Devices Inc)IC ADC 16BIT 195KSPS 44-MQFP PDF資料下載
參數資料
| 型號： | AD7722ASZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 14/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16BIT 195KSPS 44-MQFP |
| 標準包裝： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 220k |
| 數據接口： | 串行，并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 375mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-QFP |
| 供應商設備封裝： | 44-MQFP（10x10） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 1 個差分，單極；1 個差分，雙極 |
REV. B
AD7722
–21–
To interface the AD7722 to other DSPs, the master clock
frequency of the AD7722 can be reduced so that the SCO
frequency equals the maximum allowable frequency of the serial
clock input to the DSP. When the AD7722 is operated with a
lower CLKIN frequency (< 10 MHz), DSPs, such as the
TMS320C20/C25 and DSP56000/1, can be used.
Figures 26 to 28 show the interfaces between the AD7722 and
several DSPs. In all cases, the interface control pins, TSI, DOE,
SFMT, CFMT, SYNC, and FSI, can be permanently hardwired
together to either DGND or DVDD. Alternatively, SFMT or
CFMT can be tied either high or low to configure the serial data
interface for the particular format required by the DSP. The
frame synchronization signal, FSI, can be applied from the user’s
system control logic.
FSO
SDO
SCO
AD7722
RFS
DR
SCLK
ADSP-21xx
Figure 26. AD7722 to ADSP-21xx Interface
FSO
SDO
SCO
SC1
SRD
SCK
AD7722
DSP56001/2/3
Figure 27. AD7722 to DSP56000 Interface
FSO
SDO
SCO
FSR
DR
CLKR
AD7722
TMS320Cxx
Figure 28. AD7722 to TMS320C20/TMS320C25/
TMS320C50 Interface
CLKIN
RESET/SYNC
FSI
SCO
FSO (MASTER)
FSI (SLAVE)
DOE (MASTER AND SLAVE)
SDO (MASTER)
SDO (SLAVE)
t
1
t
14
NOTE 1
t
12
t
15
t
16
NOTE 1
t
11
t
16
t
15
D4
D3
D2
D1
D0
D15
D14
D1
D0
NOTE 1:
THE STATE OF FSI CANNOT BE CHANGED
4 CLKIN CYCLES BEFORE A FSO EDGE.
Figure 25. Timing for 2-Channel Multiplexed Operation
Grounding and Layout
The analog and digital power supplies to the AD7722 are indepen-
dent and separately pinned out to minimize coupling between
analog and digital sections within the device. The AD7722 should
be treated as an analog component and grounded and decoupled
to the analog ground plane. All the AD7722 ground pins should
be soldered directly to a ground plane to minimize series induc-
tance. All converter power pins should be decoupled to the analog
ground plane. To achieve the best decoupling, place surface-
mount capacitors as close as possible to the device, ideally right
up against the device pins.
The printed circuit board that houses the AD7722 should use
separate ground planes for the analog and digital interface
circuitry. All converter power pins should be decoupled to the
analog ground plane, and all interface logic circuit power pins
should be decoupled to the digital ground plane. This facili-
tates the use of ground planes, which can physically separate
sensitive analog components from the noisy digital system.
Digital and analog ground planes should only be joined in one
place and should not overlap to minimize capacitive coupling
between them.
Separate power supplies for AVDD and DVDD are also highly
desirable. The digital supply pin DVDD should be powered from
a separate analog supply, but if necessary DVDD may share its
power connection to AVDD (see the connection diagram in
Figure 29). The 10
resistor, in series with the DV
DD pin, is
required to dampen the effects of the fast switching currents into
the digital section of the AD7722. The ferrite is also recommended
to filter high frequency signals from corrupting the analog
power supply.
A minimum etch technique is generally best for ground planes
because it gives the best shielding. Noise can be minimized by
paying attention to the system layout and preventing different
signals from interfering with each other. High level analog signals
should be separated from low level analog signals, and both should
be kept away from digital signals. In waveform sampling and
reconstruction systems, the sampling clock (CLKIN) is as vulner-
able to noise as any analog signal. CLKIN should be isolated from
相關PDF資料 |
PDF描述 |
|---|---|
| AD7723BSZ-REEL | IC ADC 16BIT SIGMA-DELTA 44MQFP |
| AD7725BSZ | IC ADC 16BIT PROG 44MQFP |
| AD7730BN | IC ADC TRANSDUCER BRIDGE 24-DIP |
| AD7731BN | IC ADC 24BIT SIGMA-DELTA 24-DIP |
| AD7732BRU | IC ADC 24BIT 2-CH 28-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7722CSZ | 制造商:Analog Devices 功能描述: |
| AD7723 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 1.2 MSPS CMOS, Sigma-Delta ADC |
| AD7723BS | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 19.2Msps 16-bit Parallel/Serial 44-Pin MQFP 制造商:Analog Devices 功能描述:Analog-Digital Converter IC Number of Bi |
| AD7723BS-REEL | 制造商:Analog Devices 功能描述:Single ADC Delta-Sigma 19.2Msps 16-bit Parallel/Serial 44-Pin MQFP T/R |
| AD7723BSZ | 功能描述:IC ADC 16BIT SIGMA-DELTA 44MQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
發布緊急采購，3分鐘左右您將得到回復。