- 您現在的位置：買賣IC網 > PDF目錄375238 > AD7691BRMZ-RL7 (ANALOG DEVICES INC) 18-Bit, 1.5 LSB INL, 250 kSPS PulSAR Differential ADC in MSOP/QFN PDF資料下載
參數資料
| 型號： | AD7691BRMZ-RL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 18-Bit, 1.5 LSB INL, 250 kSPS PulSAR Differential ADC in MSOP/QFN |
| 中文描述： | 1-CH 18-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO10 |
| 封裝： | LEAD FREE, MO-187BA, MSOP-10 |
| 文件頁數： | 24/28頁 |
| 文件大?。?/td> | 682K |
| 代理商： | AD7691BRMZ-RL7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁
AD7691
APPLICATION HINTS
LAYOUT
The printed circuit board that houses the AD7691 should be
designed so that the analog and digital sections are separated
and confined to certain areas of the board. The pinout of the
AD7691, with all its analog signals on the left side and all its
digital signals on the right side, eases this task.
Rev. 0 | Page 24 of 28
Avoid running digital lines under the device because this couples
noise onto the die unless a ground plane under the AD7691 is
used as a shield. Fast switching signals, such as CNV or clocks,
should not run near analog signal paths. Crossover of digital
and analog signals should be avoided.
At least one ground plane should be used. It could be common
or split between the digital and analog sections. In the latter
case, the planes should be joined underneath the AD7691.
The AD7691 voltage reference input, REF, has a dynamic input
impedance and should be decoupled with minimal parasitic
inductances. This is done by placing the reference decoupling
ceramic capacitor close to, ideally right up against, the REF and
GND pins and connecting them with wide, low impedance traces.
Finally, the power supplies, VDD and VIO, of the AD7691
should be decoupled with ceramic capacitors, typically 100 nF,
placed close to the AD7691 and connected using short and wide
traces to provide low impedance paths and reduce the effect of
glitches on the power supply lines.
An example of a layout following these rules is shown in
Figure 46 and Figure 47.
EVALUATING THE AD7691’S PERFORMANCE
Other recommended layouts for the AD7691 are outlined
in the documentation of the evaluation board for the AD7691
(EVAL-AD7691-CB). The evaluation board package includes
a fully assembled and tested evaluation board, documentation,
and software for controlling the board from a PC via the
EVAL-CONTROL BRD3.
0
Figure 46. Example Layout of the AD7691 (Top Layer)
0
Figure 47. Example Layout of the AD7691 (Bottom Layer)
相關PDF資料 |
PDF描述 |
|---|---|
| AD7710AN | Signal Conditioning ADC |
| AD7710AQ | Signal Conditioning ADC |
| AD7710AR | Signal Conditioning ADC |
| AD7710SQ | Signal Conditioning ADC |
| AD7710* | Signal Conditioning ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7693 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit Lower Power |
| AD76931 | 制造商:AD 制造商全稱:Analog Devices 功能描述:18-Bit, 2 MSPS PulSAR 15 mW ADC in LFCSP (QFN) |
| AD7693BCPZ | 制造商:Analog Devices 功能描述:ADC SGL SAR 500KSPS 16BIT SERL 10LFCSP - Rail/Tube |
| AD7693BCPZ-R2 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD7693BCPZRL | 功能描述:IC ADC 16BIT 500KSPS 10LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。