- 您現在的位置：買賣IC網 > PDF目錄10666 > AD7655ASTZ (Analog Devices Inc)IC ADC 16BIT 1MSPS QUAD 48-LQFP PDF資料下載
參數資料
| 型號： | AD7655ASTZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 18/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16BIT 1MSPS QUAD 48-LQFP |
| 標準包裝： | 1 |
| 系列： | PulSAR® |
| 位數： | 16 |
| 采樣率（每秒）： | 1M |
| 數據接口： | 串行，并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 135mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 2 個差分，單極 |
| 產品目錄頁面： | 778 (CN2011-ZH PDF) |
| 配用： | EVAL-AD7655CBZ-ND - BOARD EVALUATION FOR AD7655 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD7655
Rev. B | Page 25 of 28
APPLICATION HINTS
LAYOUT
The AD7655 has very good immunity to noise on the power
supplies. However, care should still be taken with regard to
grounding layout.
The printed circuit board that houses the AD7655 should be
designed so the analog and digital sections are separated and
confined to certain areas of the board. This facilitates the use of
ground planes that can be separated easily. Digital and analog
ground planes should be joined in only one place, preferably
underneath the AD7655, or as close as possible to the AD7655.
If the AD7655 is in a system where multiple devices require
analog-to-digital ground connections, the connection should
still be made at one point only, a star ground point that should
be established as close as possible to the AD7655.
Avoid unning digital lines under the device because these
couple noise onto the die. The analog ground plane should be
allowed to run under the AD7655 to avoid noise coupling. Fast
switching signals such as CNVST or clocks should be shielded
with digital ground to avoid radiating noise to other sections of
the board and should never run near analog signal paths.
Crossover of digital and analog signals should be avoided.
Traces on different but close layers of the board should run at
right angles to each other. This reduces the effect of crosstalk
through the board.
The power supply lines to the AD7655 should use as large a
trace as possible to provide low impedance paths and reduce the
effect of glitches on the power supply lines. Good decoupling is
also important to lower the supply impedance presented to the
AD7655 and to reduce the magnitude of the supply spikes.
Decoupling ceramic capacitors, typically 100 nF, should be
placed on each power supply pin—AVDD, DVDD, and
OVDD—close to, and ideally right up against these pins and
their corresponding ground pins. Additionally, low ESR 10 μF
capacitors should be located near the ADC to further reduce
low frequency ripple.
The DVDD supply of the AD7655 can be a separate supply or
can come from the analog supply AVDD or the digital interface
supply OVDD. When the system digital supply is noisy or when
fast switching digital signals are present, if no separate supply is
available, the user should connect DVDD to AVDD through an
RC filter (see Figure 17) and the system supply to OVDD and
the remaining digital circuitry. When DVDD is powered from
the system supply, it is useful to insert a bead to further reduce
high frequency spikes.
The AD7655 has five ground pins: INGND, REFGND, AGND,
DGND, and OGND. INGND is used to sense the analog input
signal. REFGND senses the reference voltage and, because it
carries pulsed currents, should be a low impedance return to
the reference. AGND is the ground to which most internal
ADC analog signals are referenced; it must be connected with
the least resistance to the analog ground plane. DGND must be
tied to the analog or digital ground plane depending on the
configuration. OGND is connected to the digital system
ground.
EVALUATING THE AD7655 PERFORMANCE
A recommended layout for the AD7655 is outlined in the
EVAL-AD7655CB evaluation board documentation. The
evaluation board package includes a fully assembled and tested
evaluation board, documentation, and software for controlling
the board from a PC via the EVAL-CONTROL-BRD3.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-JTP-MY-F3 | CONVERTER MOD DC/DC 13.8V 50W |
| VE-J12-MW-F1 | CONVERTER MOD DC/DC 15V 100W |
| VE-JTP-MY-F2 | CONVERTER MOD DC/DC 13.8V 50W |
| VE-2NJ-IX-B1 | CONVERTER MOD DC/DC 36V 75W |
| LMX331AUK-T | IC COMPARATOR GP LV TINY SOT23-5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7655ASTZ | 制造商:Analog Devices 功能描述:CONVERTER A/D ((NW)) |
| AD7655ASTZRL | 功能描述:IC ADC 16BIT 4CHAN 48LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7655SCP-EP-RL | 制造商:Analog Devices 功能描述:ADC Single SAR 1Msps 16-bit Parallel/Serial 48-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:LOW COST 4-CHANNEL 1 MSPS 16-BIT ADC - Tape and Reel 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:IC ADC 16B PAR/SRL 1MSPS 48LFCSP 制造商:Analog Devices 功能描述:Analog to Digital Converters - ADC 4Ch 1MSPS 16-Bit Low Cost 制造商:Analog Devices 功能描述:CONVERTER - ADC |
| AD7656 | 制造商:AD 制造商全稱:Analog Devices 功能描述:250 kSPS, 6-Channel,Simultaneous Sampling, Bipolar 12/14/16-Bit ADC |
| AD7656-1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:250 kSPS, 6-Channel, Simultaneous Sampling, Bipolar, 16-/14-/12-Bit ADC |
發布緊急采購，3分鐘左右您將得到回復。