- 您現在的位置：買賣IC網 > PDF目錄10669 > AD7651ASTZ (Analog Devices Inc)IC ADC 16BIT 100KSPS 48-LQFP PDF資料下載
參數資料
| 型號： | AD7651ASTZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 3/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16BIT 100KSPS 48-LQFP |
| 標準包裝： | 1 |
| 系列： | PulSAR® |
| 位數： | 16 |
| 采樣率（每秒）： | 100k |
| 數據接口： | 串行，并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 45mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 2 個偽差分，單極 |
| 產品目錄頁面： | 778 (CN2011-ZH PDF) |
| 配用： | EVAL-AD7651CBZ-ND - BOARD EVALUATION FOR AD7651 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD7651
DEFINITIONS OF SPECIFICATIONS
Integral Nonlinearity Error (INL)
Linearity error refers to the deviation of each individual code
from a line drawn from negative full scale through positive full
scale. The point used as negative full scale occurs LSB before
the first code transition. Positive full scale is defined as a level
1 LSB beyond the last code transition. The deviation is
measured from the middle of each code to the true straight line.
Differential Nonlinearity Error (DNL)
In an ideal ADC, code transitions are 1 LSB apart. Differential
nonlinearity is the maximum deviation from this ideal value. It
is often specified in terms of resolution for which no missing
codes are guaranteed.
Full-Scale Error
The last transition (from 011…10 to 011…11 in twos
complement coding) should occur for an analog voltage 1 LSB
below the nominal full scale (2.49994278 V for the 0 V to 2.5 V
range). The full-scale error is the deviation of the actual level of
the last transition from the ideal level.
Unipolar Zero Error
The first transition should occur at a level LSB above analog
ground (19.073 V for the 0 V to 2.5 V range). Unipolar zero
error is the deviation of the actual transition from that point.
Spurious-Free Dynamic Range (SFDR)
SFDR is the difference, in decibels (dB), between the rms
amplitude of the input signal and the peak spurious signal.
Effective Number Of Bits (ENOB)
ENOB is a measurement of the resolution with a sine wave
input. It is related to S/(N+D) by the following formula:
ENOB = (S/[N+D]dB – 1.76)/6.02
and is expressed in bits.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first five harmonic
components to the rms value of a full-scale input signal, and is
expressed in decibels.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the actual input signal to the
rms sum of all other spectral components below the Nyquist
frequency, excluding harmonics and dc. The value for SNR is
expressed in decibels.
Signal-to-(Noise + Distortion) Ratio (S/[N+D])
S/(N+D) is the ratio of the rms value of the actual input signal
to the rms sum of all other spectral components below the
Nyquist frequency, including harmonics but excluding dc. The
value for S/(N+D) is expressed in decibels.
Aperture Delay
Aperture delay is a measure of the acquisition performance and
is measured from the falling edge of the CNVST input to when
the input signal is held for a conversion.
Transient Response
Transient response is the time required for the AD7651 to
achieve its rated accuracy after a full-scale step function is
applied to its input.
Overvoltage Recovery
Overvoltage recovery is the time required for the ADC to
recover to full accuracy after an analog input signal 150% of the
full-scale value is reduced to 50% of the full-scale value.
Reference Voltage Temperature Coefficient
Reference voltage temperature coefficient is the change of
internal reference voltage output voltage V over the operating
temperature range and normalized by the output voltage at
25°C, expressed in ppm/°C. The equation follows:
6
1
2
1
2
10
)
–
(
)
C
25
(
)
(
–
)
(
)
/
(
×
°
=
°
T
V
T
V
T
V
C
ppm
TCV
where:
V(25°C) = V at +25°C
V(T2) = V at Temperature 2 (+85°C)
V(T1) = V at Temperature 1 (–40°C)
Rev. 0 | Page 11 of 28
相關PDF資料 |
PDF描述 |
|---|---|
| VI-2WM-IX-B1 | CONVERTER MOD DC/DC 10V 75W |
| LTC1402CGN#PBF | IC ADC 12BIT 2.2MSPS SHDN 16SSOP |
| VE-2N2-IX-B1 | CONVERTER MOD DC/DC 15V 75W |
| VE-26Y-IV-B1 | CONVERTER MOD DC/DC 3.3V 99W |
| CS5532-BSZ | IC ADC 24BIT 2CH W/LNA 20SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7651ASTZ | 制造商:Analog Devices 功能描述:16BIT SAR ADC REF 7651 LQFP48 |
| AD7651ASTZRL | 功能描述:IC ADC 16BIT UNIPOLAR 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7652 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit 1 MSPS SAR Unipolar ADC with Ref |
| AD7652ACP | 制造商:Analog Devices 功能描述:ADC Single SAR 500ksps 16-bit Parallel/Serial 48-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:16-BIT 500KSPS SAR UNIPOLAR ADC W/ REF - Bulk 制造商:Analog Devices 功能描述:16BIT SAR ADC REF 7652 LFSCP-48 |
| AD7652ACPRL | 制造商:Analog Devices 功能描述:ADC Single SAR 500ksps 16-bit Parallel/Serial 48-Pin LFCSP EP T/R |
發布緊急采購，3分鐘左右您將得到回復。