- 您現在的位置：買賣IC網 > PDF目錄10084 > AD7634BCPZRL (Analog Devices Inc)IC ADC 18BIT DIFF BIPO 48-LFCSP PDF資料下載
參數資料
| 型號： | AD7634BCPZRL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 25/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 18BIT DIFF BIPO 48-LFCSP |
| 標準包裝： | 2,500 |
| 系列： | PulSAR® |
| 位數： | 18 |
| 采樣率（每秒）： | 670k |
| 數據接口： | 串行，并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 225mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 48-LFCSP-VQ（7x7） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個差分，單極；1 個差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Data Sheet
AD7634
Rev. B | Page 31 of 32
APPLICATION INFORMATION
LAYOUT GUIDELINES
While the AD7634 has very good immunity to noise on the
power supplies, exercise care with the grounding layout. To facili-
tate the use of ground planes that can be easily separated, design
the printed circuit board that houses the AD7634 so that the
analog and digital sections are separated and confined to certain
areas of the board. Digital and analog ground planes should be
joined in only one place, preferably underneath the AD7634, or
as close as possible to the AD7634. If the AD7634 is in a system
where multiple devices require analog-to-digital ground connect-
ions, the connections should still be made at one point only, a
star ground point, established as close as possible to the AD7634.
To prevent coupling noise onto the die, avoid radiating noise,
and reduce feedthrough:
Do not run digital lines under the device.
Do run the analog ground plane under the AD7634.
Do shield fast switching signals, like CNVST or clocks, with
digital ground to avoid radiating noise to other sections of
the board, and never run them near analog signal paths.
Avoid crossover of digital and analog signals.
Run traces on different but close layers of the board, at right
angles to each other, to reduce the effect of feedthrough through
the board.
The power supply lines to the AD7634 should use as large a trace
as possible to provide low impedance paths and reduce the effect
of glitches on the power supply lines. Good decoupling is also
important to lower the impedance of the supplies presented to
the AD7634, and to reduce the magnitude of the supply spikes.
Decoupled ceramic capacitors, typically 100 nF, should be placed
on each of the power supplies pins, AVDD, DVDD, and OVDD,
VCC, and VEE. The capacitors should be placed close to, and
ideally right up against, these pins and their corresponding ground
pins. Additionally, low ESR 10 μF capacitors should be located
in the vicinity of the ADC to further reduce low frequency ripple.
The DVDD supply of the AD7634 can be either a separate supply
or come from the analog supply, AVDD, or from the digital
interface supply, OVDD. When the system digital supply is noisy,
or fast switching digital signals are present, and no separate supply
is available, it is recommended to connect the DVDD digital supply
to the analog supply AVDD through an RC filter, and to connect
the system supply to the interface digital supply OVDD and the
remaining digital circuitry. See Figure 27 for an example of this
configuration. When DVDD is powered from the system supply,
it is useful to insert a bead to further reduce high frequency spikes.
The AD7634 has four different ground pins: REFGND, AGND,
DGND, and OGND.
REFGND senses the reference voltage and, because it carries
pulsed currents, should be a low impedance return to the
reference.
AGND is the ground to which most internal ADC analog
signals are referenced; it must be connected with the least
resistance to the analog ground plane.
DGND must be tied to the analog or digital ground plane
depending on the configuration.
OGND is connected to the digital system ground.
The layout of the decoupling of the reference voltage is important.
To minimize parasitic inductances, place the decoupling capacitor
close to the ADC and connect it with short, thick traces.
EVALUATING PERFORMANCE
A recommended layout for the AD7634 is outlined in the EVAL-
AD7634EDZ evaluation board documentation. The evaluation
board package includes a fully assembled and tested evaluation
board, documentation, and software for controlling the board
from a PC via the EVAL-CED1Z.
相關PDF資料 |
PDF描述 |
|---|---|
| D38999/26WD15PC | CONN PLUG 15POS STRAIGHT W/PINS |
| IDT72V235L15TF8 | IC FIFO SYNC 2048X18 15NS 64QFP |
| AD774BJNZ | IC ADC 12BIT W/BUFF REF 28DIP |
| VE-2N1-IW-F3 | CONVERTER MOD DC/DC 12V 100W |
| IDT72245LB25TF8 | IC FIFO 1024X18 SYNC 25NS 64QFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7634BSTZ | 功能描述:IC ADC 18BIT DIFF BIPO 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7634BSTZRL | 功能描述:IC ADC 18BIT DIFF BIPO 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD7641 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 750 kSPS, Unipolar/Bipolar Programmable Input PulSAR ADC |
| AD7641ACP | 制造商:Analog Devices 功能描述:ADC SGL SAR 2MSPS 18BIT PARALLEL/SERL 48LFCSP - Trays |
| AD7641ACPRL | 制造商:Analog Devices 功能描述:ADC SGL SAR 2MSPS 18BIT PARALLEL/SERL 48LFCSP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。