- 您現在的位置：買賣IC網 > PDF目錄362103 > AD7440 AD7450A/AD7440: Differential Input. 1MSPS. 12-Bit ADC in 8-lead SOT-23 Preliminary Data Sheet (Rev. PrF. 3/03) PDF資料下載
參數資料
| 型號： | AD7440 |
| 英文描述： | AD7450A/AD7440: Differential Input. 1MSPS. 12-Bit ADC in 8-lead SOT-23 Preliminary Data Sheet (Rev. PrF. 3/03) |
| 中文描述： | AD7450A/AD7440：差分輸入。 1MSPS。 12位ADC，采用8引腳SOT - 23的初步數據（牧師脈沖重復頻率。3 / 03） |
| 文件頁數： | 9/24頁 |
| 文件大?。?/td> | 914K |
| 代理商： | AD7440 |
REV. PrF
PRELIMINARY TECHNICAL DATA
–9–
AD7450A/AD7440
TERMINOLOGY
Signal to (Noise + Distortion) Ratio
This is the measured ratio of signal to (noise + distortion)
at the output of the ADC. The signal is the rms amplitude
of the fundamental. Noise is the sum of all
nonfundamental signals up to half the sampling frequency
(f
S
/2), excluding dc. The ratio is dependent on the number
of quantization levels in the digitization process; the more
levels, the smaller the quantization noise. The theoretical
signal to (noise + distortion) ratio for an ideal N-bit con-
verter with a sine wave input is given by:
Signal to
(
Noise + Distortion
)
=
(6.02
N +
1.76)
dB
Thus for a 12-bit converter, this is 74 dB and for a 10-bit
converter, this is 62dB.
Total Harmonic Distortion
Total harmonic distortion (THD) is the ratio of the rms
sum of harmonics to the fundamental. For the AD7450, it
is defined as:
THD (dB )
=
20 log
V
2
2
+
V
3
2
+
V
4
2
+
V
5
2
+
V
6
2
V
1
where
V
1
is the rms amplitude of the fundamental and
V
2
,
V
3
,
V
4
,
V
5
and
V
6
are the rms amplitudes of the second to
the sixth harmonics.
Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is defined as the ratio of
the rms value of the next largest component in the ADC
output spectrum (up to f
S
/2 and excluding dc) to the rms
value of the fundamental. Normally, the value of this
specification is determined by the largest harmonic in the
spectrum, but for ADCs where the harmonics are buried
in the noise floor, it will be a noise peak.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa
and fb, any active device with nonlinearities will create
distortion products at sum and difference frequencies of
mfa ± nfb where m, n = 0, 1, 2, 3, etc. Intermodulation
distortion terms are those for which neither m nor n are
equal to zero. For example, the second order terms in-
clude (fa + fb) and (fa – fb), while the third order terms
include (2fa + fb), (2fa – fb), (fa + 2fb) and (fa – 2fb).
The AD7450A/AD7440 is tested using the CCIF standard
where two input frequencies near the top end of the input
bandwidth are used. In this case, the second order terms
are usually distanced in frequency from the original sine
waves while the third order terms are usually at a fre-
quency close to the input frequencies. As a result, the
second and third order terms are specified separately. The
calculation of the intermodulation distortion is as per the
THD specification where it is the ratio of the rms sum of
the individual distortion products to the rms amplitude of
the sum of the fundamentals expressed in dBs.
Aperture Delay
This is the amount of time from the leading edge of the
sampling clock until the ADC actually takes the sample.
Aperture Jitter
This is the sample to sample variation in the effective
point in time at which the actual sample is taken.
Full Power Bandwidth
The full power bandwidth of an ADC is that input fre-
quency at which the amplitude of the reconstructed
fundamental is reduced by 0.1dB or 3dB for a full scale
input.
Common Mode Rejection Ratio (CMRR)
The Common Mode Rejection Ratio is defined as the
ratio of the power in the ADC output at full-scale fre-
quency, f, to the power of a 200mV p-p sine wave applied
to the Common Mode Voltage of V
IN+
and V
IN-
of fre-
quency fs:
CMRR (dB) = 10log(Pf/Pfs)
Pf
is the power at the frequncy f in the ADC output;
Pfs
is
the power at frequency fs in the ADC output.
Integral Nonlinearity (INL)
This is the maximum deviation from a straight line pass-
ing through the endpoints of the ADC transfer function.
Differential Nonlinearity (DNL)
This is the difference between the measured and the ideal 1
LSB change between any two adjacent codes in the ADC.
Zero Code Error
This is the deviation of the midscale code transition (111...111
to 000...000) from the ideal V
IN+
-V
IN -
(i.e., 0LSB).
This is the deviation of the last code transition (011...110 to
011...111) from the ideal V
IN+
-V
IN-
(i.e., +V
REF
- 1LSB), after
the Zero Code Error has been adjusted out.
Negative Gain Error
This is the deviation of the first code transition (100...000 to
100...001) from the ideal V
IN+
-V
IN -
(i.e., -V
REF
+ 1LSB), after
the Zero Code Error has been adjusted out.
Track/Hold Acquisition Time
The track/hold acquisition time is the minimum time
required for the track and hold amplifier to remain in
track mode for its output to reach and settle to within 0.5
LSB of the applied input signal.
Power Supply Rejection Ratio (PSRR)
The power supply rejection ratio is defined as the ratio of
the power in the ADC output at full-scale frequency, f, to
the power of a 200mV p-p sine wave applied to the ADC
V
DD
supply of frequency fs. The frequency of this input
varies from 1kHz to 1MHz.
PSRR (dB) = 10 log (Pf/Pfs)
Pf
is the power at frequency f in the ADC output;
Pfs
is
the power at frequency fs in the ADC output.
相關PDF資料 |
PDF描述 |
|---|---|
| AD744CQ | Voltage-Feedback Operational Amplifier |
| AD7450A | AD7450A/AD7440: Differential Input. 1MSPS. 12-Bit ADC in 8-lead SOT-23 Preliminary Data Sheet (Rev. PrF. 3/03) |
| AD744JCHIPS | Rectangular Connector; Series:516; No. of Contacts:20; Gender:Male; Color:Grey; Leaded Process Compatible:Yes; Insulator Material:Polycarbonate RoHS Compliant: Yes |
| AD744JN | Precision, 500 ns Settling BiFET Op Amp |
| AD744JR | Precision, 500 ns Settling BiFET Op Amp |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7440BRM | 制造商:Analog Devices 功能描述:ADC Single SAR 1Msps 10-bit Serial 8-Pin MSOP 制造商:Analog Devices 功能描述:ADC SGL SAR 1MSPS 10-BIT SERL 8MSOP - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:10-BIT DIFF I/PUT, 1MSPS SAR ADC I.C. - Bulk 制造商:Analog Devices 功能描述:10BIT SAR ADC DIFF I/P SMD 7440 |
| AD7440BRM-REEL7 | 功能描述:IC ADC 10BIT W/DIFF INP 8-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7440BRMZ | 功能描述:IC ADC 10BIT DIFF IN 1MSPS 8MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯(lián) 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7440BRMZ2 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Differential Input, 1 MSPS ADCs in an 8-Lead SOT-23 |
| AD7440BRT | 制造商:AD 制造商全稱:Analog Devices 功能描述:Differential Input, 1 MSPS ADCs in an 8-Lead SOT-23 |
發(fā)布緊急采購，3分鐘左右您將得到回復。