- 您現在的位置：買賣IC網 > PDF目錄373892 > AD670KN (ANALOG DEVICES INC) Low Cost Signal Conditioning 8-Bit ADC PDF資料下載
參數資料
| 型號： | AD670KN |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | Low Cost Signal Conditioning 8-Bit ADC |
| 中文描述： | 2-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PDIP20 |
| 封裝： | PLASTIC, DIP-20 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 364K |
| 代理商： | AD670KN |
AD670
REV. A
–9–
APPLYING THE AD670
The AD670 has been designed for ease of use, system compat-
ibility, and minimization of external components. Transducer
interfaces generally require signal conditioning and preampli-
fication before the signal can be converted. The AD670 will
reduce and even eliminate this excess circuitry in many cases.
To illustrate the flexibility and superior solution that the AD670
can bring to a transducer interface problem, the following dis-
cussions are offered.
Temperature Measurements
Temperature transducers are one of the most common sources
of analog signals in data acquisition systems. These sensors re-
quire circuitry for excitation and preamplification/buffering. The
instrumentation amplifier input of the AD670 eliminates the
need for this signal conditioning. The output signals from tem-
perature transducers are generally sufficiency slow that a
sample/hold amplifier is not required. Figure 12 shows tile
AD590 IC temperature transducer interfaced to the AD670.
The AD580 voltage reference is used to offset the input for 0
°
C
calibration. The current output of the AD590 is converted into
a voltage by R1. The high impedance unbuffered voltage is ap-
plied directly to the AD670 configured in the –128 mV to
127 mV bipolar range. The digital output will have a resolution
of 1
°
C.
Figure 12. AD670 Temperature Transducer lnterface
Platinum RTDs are also a popular, temperature transducer.
Typical RTDs have a resistance of 100
at 0
°
C and change re-
sistance 0.4
per
°
C. If a consent excitation current is caused
to flow in the RTD, the change in voltage drop will be a mea-
sure of the change in temperature. Figure 13 shows such a
method and the required connections to the AD670. The
AD580 2.5 V reference provides the accurate voltage for the ex-
citation current and range offsetting for the RTD. The op amp
is configured to force a constant 2.5 mA current through the
RTD. The differential inputs of the AD670 measure the differ-
ence between a fixed offset voltage and the temperature depen-
dent output of the op amp which varies with the resistance of
the RTD. The RTD change of approximately 0.4
/
°
C results
in a 1 mV/
°
C voltage change. With the AD670 in the 1 mV/LSB
range, temperatures from 0
°
C to 255
°
C can be measured.
Figure 13. Low Cost RTD Interface
Differential temperature measurements can be made using an
AD590 connected to each of the inputs as shown in Figure 14.
This configuration will allow the user to measure the relative
temperature difference between two points with a 1
°
C resolu-
tion. Although the internal 1k and 9k resistors on the inputs
have
±
20% tolerance, trimming the AD590 is unnecessary as
most differential temperature applications are concerned with
the relative differences between the two. However, the user may
see up to a 20% scale factor error in the differential temperature
to digital output transfer curve.
This scale factor error can be eliminated through a software cor-
rection. Offset corrections can be made by adjusting for any dif-
ference that results when both sensors are held at the same
temperature. A span adjustment can then be made by immers-
ing one AD590 in an ice bath and one in boiling water and
eliminating any deviation from 100
°
C. For a low cost version of
this setup, the plastic AD592 can be substituted for the AD590.
Figure 14. Differential Temperature Measurement
Using the AD590
相關PDF資料 |
PDF描述 |
|---|---|
| AD670KP | Low Cost Signal Conditioning 8-Bit ADC |
| AD698 | Universal LVDT Signal Conditioner |
| AD698AP | ECONOLINE: REC2.2-S_DR/H1 - 2.2W DIP Package- 1kVDC Isolation- Regulated Output- UL94V-0 Package Material- Continuous Short Circiut Protection- Internal SMD design- 100% Burned In- Efficiency to 75% |
| AD698SQ | ECONOLINE: REC2.2-S_DRW(Z)/H* - 2.2W DIP Package- 1kVDC Isolation- Regulated Output- 4.5-9V, 9-18V, 18-36V, 36-72V Wide Input Range 2 : 1- UL94V-0 Package Material- Continuous Short Circiut Protection- Cost Effective- 100% Burned In- Efficiency to 84% |
| AD7001 | M83723 14C 14#16 SKT RECP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD670KNZ | 功能描述:IC ADC 8BIT SGNL COND 20DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| AD670KP | 制造商:Analog Devices 功能描述:ADC Single SAR 8-bit Parallel 20-Pin PLCC |
| AD670KPZ | 功能描述:IC ADC 8BIT SIGNAL COND 20-PLCC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD670SD | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AD670SD/883B | 功能描述:模數轉換器 - ADC 8-B Signal Condition RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
發布緊急采購，3分鐘左右您將得到回復。