- 您現在的位置：買賣IC網 > PDF目錄373887 > AD623AN (ANALOG DEVICES INC) Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier PDF資料下載
參數資料
| 型號： | AD623AN |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| 中文描述： | INSTRUMENTATION AMPLIFIER, 350 uV OFFSET-MAX, 0.8 MHz BAND WIDTH, PDIP8 |
| 封裝： | PLASTIC, DIP-8 |
| 文件頁數： | 12/16頁 |
| 文件大小： | 965K |
| 代理商： | AD623AN |
AD623
–12–
REV. C
Table I. Required Values of Gain Resistors
Desired
Gain
1% Std Table
Value of R
G
,
V
Calculated Gain
Using 1% Resistors
2
5
10
20
33
40
50
65
100
200
500
1000
100 k
24.9 k
11 k
5.23 k
3.09 k
2.55 k
2.05 k
1.58 k
1.02 k
499
200
100
2
5.02
10.09
20.12
33.36
40.21
49.78
64.29
99.04
201.4
501
1001
INPUT AND OUTPUT OFFSET VOLTAGE
The low errors of the AD623 are attributed to two sources,
input and output errors. The output error is divided by the
programmed gain when referred to the input. In practice, the
input errors dominate at high gains and the output errors domi-
nate at low gains. The total V
OS
for a given gain is calculated as:
Total Error RTI = Input Error + (Output Error/G)
Total Error RTO = (Input Error
×
G) + Output Error
RTI offset errors and noise voltages for different gains are shown
below in Table II.
Table II. RTI Error Sources
Max
Total Input
Offset Error
Max
Total Input
Offset Drift
m
V/
8
C
Total Input
Referred Noise
(nV/
√
Hz
)
Gain
m
V
m
V
m
V/
8
C
AD623A AD623B AD623A AD623B AD623A & AD623B
1
2
5
10
20
50
100
1000 200
1200
700
400
300
250
220
210
600
350
200
150
125
110
105
100
12
7
4
3
2.5
2.2
2.1
2
11
6
3
2
1.5
1.2
1.1
1
62
45
38
35
35
35
35
35
INPUT PROTECTION
Internal supply referenced clamping diodes allow the input,
reference, output and gain terminals of the AD623 to safely
withstand overvoltages of 0.3 V above or below the supplies.
This is true for all gains, and for power on and off. This last
case is particularly important since the signal source and ampli-
fier may be powered separately.
If the overvoltage is expected to exceed this value, the current
through these diodes should be limited to about 10 mA using
external current limiting resistors. This is shown in Figure 42.
The size of this resistor is defined by the supply voltage and the
required overvoltage protection.
V
OVER
V
OVER
R
LIM
R
LIM
V
OVER
2
V
S
+0.7V
10mA
R
LIM
=
1 = 10mA MAX
+V
S
2
V
S
OUTPUT
R
G
AD623
Figure 42. Input Protection
RF INTERFERENCE
All instrumentation amplifiers can rectify high frequency out-of-
band signals. Once rectified, these signals appear as dc offset
errors at the output. The circuit of Figure 43 provides good RFI
suppression without reducing performance within the in amps
pass band. Resistor R1 and capacitor C1 (and likewise, R2 and
C2) form a low-pass RC filter that has a –3 dB BW equal to:
F = 1/(2
π
R1C1). Using the component values shown, this
filter has a –3 dB bandwidth of approximately 40 kHz. Resistors
R1 and R2 were selected to be large enough to isolate the
circuit’s input from the capacitors, but not large enough to
significantly increase the circuit’s noise. To preserve common-
mode rejection in the amplifier’s pass band, capacitors C1 and
C2 need to be 5% or better units, or low cost 20% units can be
tested and “binned” to provide closely matched devices.
Capacitor C3 is needed to maintain common-mode rejection at
the low frequencies. R1/R2 and C1/C2 form a bridge circuit
whose output appears across the in amp’s input pins. Any
mismatch between C1 and C2 will unbalance the bridge and
reduce common-mode rejection. C3 ensures that any RF signals
R
G
R
G
R
G
V
IN
+V
S
+2.5V TO +6V
V
OUT
REF (INPUT)
–V
S
0.1
m
F
10
m
F
–2.5V TO –6V
REF
OUTPUT
0.1
m
F
10
m
F
+3V TO +12V
R
G
R
G
R
G
V
IN
+V
S
V
OUT
REF (INPUT)
REF
OUTPUT
0.1
m
F
10
m
F
a. Dual Supply
b. Single Supply
Figure 41. Basic Connections
相關PDF資料 |
PDF描述 |
|---|---|
| AD623AR | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| AD623AR-REEL7 | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| AD623ARM | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| AD623ARM-REEL | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| AD623ARM-REEL7 | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD623ANZ | 功能描述:IC AMP INST R-R LP 8DIP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:30pA 電壓 - 輸入偏移:2000µV 電流 - 電源:200µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
| AD623AR | 功能描述:IC AMP INST R-R LP 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:30pA 電壓 - 輸入偏移:2000µV 電流 - 電源:200µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
| AD623AR | 制造商:Analog Devices 功能描述:SEMICONDUCTORS |
| AD623ARM | 制造商:Analog Devices 功能描述:SP Amp INSTR Amp Single R-R O/P 制造商:Analog Devices 功能描述:IC AMP INSTRUMENTATION |
| AD623ARM-REEL | 制造商:Analog Devices 功能描述:SP Amp INSTR Amp Single R-R O/P |
發布緊急采購，3分鐘左右您將得到回復。