- 您現在的位置：買賣IC網 > PDF目錄373887 > AD623AN (ANALOG DEVICES INC) Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier PDF資料下載
參數資料
| 型號： | AD623AN |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| 中文描述： | INSTRUMENTATION AMPLIFIER, 350 uV OFFSET-MAX, 0.8 MHz BAND WIDTH, PDIP8 |
| 封裝： | PLASTIC, DIP-8 |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 965K |
| 代理商： | AD623AN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁
AD623
–11–
REV. C
Figure 38. Gain Nonlinearity (G = –100, 15 ppm/Div)
V–
0
0.5
S
1
(V–) +0.5
(V+) –1.5
V+
(V+) –1.5
(V+) –0.5
1.5
OUTPUT CURRENT – mA
2
Figure 39. Output Voltage Swing vs. Output Current
THEORY OF OPERATION
The AD623 is an instrumentation amplifier based on a modified
classic three op amp approach, to assure single or dual supply
operation even at common-mode voltages at the negative supply
rail. Low voltage offsets, input and output, as well as absolute
gain accuracy, and one external resistor to set the gain, make the
AD623 one of the most versatile instrumentation amplifiers in
its class.
The input signal is applied to PNP transistors acting as voltage
buffers and providing a common-mode signal to the input
amplifiers (Figure 40). An absolute value 50 k
resistor in each
of the amplifiers’ feedback assures gain programmability.
The differential output is
V
O
=
1
+
100
k
R
G
V
C
The differential voltage is then converted to a single-ended
voltage using the output amplifier, which also rejects any common-
mode signal at the output of the input amplifiers.
Since all the amplifiers can swing to either supply rails, as well
as have their common-mode range extended to below the nega-
tive supply rail, the range over which the AD623 can operate is
further enhanced (Figures 19 and 20).
The output voltage at Pin 6 is measured with respect to the
potential at Pin 5. The impedance of the reference pin is 100k
,
so in applications requiring V/I conversion, a small resistor
between Pins 5 and 6 is all that is needed.
+
–
50k
V
50k
V
50k
V
POS SUPPLY
7
INVERTING
2
1
4
50k
V
50k
V
50k
V
8
4
NEG SUPPLY
NON-
INVERTING
3
7
GAIN
OUT
6
REF
5
+
–
+
–
Figure 40. Simplified Schematic
The bandwidth of the AD623 is reduced as the gain is increased,
since all the amplifiers are of voltage feedback type. At unity
gain, it is the output amplifier that limits the bandwidth. There-
fore even at higher gains the AD623 bandwidth does not roll off
as quickly.
APPLICATIONS
Basic Connection
Figure 41 shows the basic connection circuit for the AD623.
The +V
S
and –V
S
terminals are connected to the power supply.
The supply can be either bipolar (V
S
=
±
2.5 V to
±
6 V) or
single supply (–V
S
= 0 V, +V
S
= 3.0 V to 12 V). Power supplies
should be capacitively decoupled close to the devices power
pins. For best results, use surface mount 0.1
μ
F ceramic chip
capacitors and 10
μ
F electrolytic tantalum capacitors.
The input voltage, which can be either single-ended (tie either
–IN or +IN to ground) or differential is amplified by the pro-
grammed gain. The output signal appears as the voltage difference
between the Output pin and the externally applied voltage on
the REF input. For a ground referenced output, REF should be
grounded.
GAIN SELECTION
The AD623’s gain is resistor programmed by R
G
, or more pre-
cisely, by whatever impedance appears between Pins 1 and 8.
The AD623 is designed to offer accurate gains using 0.1%–1%
tolerance resistors. Table I shows required values of R
G
for
various gains. Note that for G = 1, the R
G
terminals are uncon-
nected (R
G
=
`
). For any arbitrary gain, R
G
can be calculated
by using the formula
R
G
= 100
k
/(
G
– 1)
REFERENCE TERMINAL
The reference terminal potential defines the zero output voltage
and is especially useful when the load does not share a precise
ground with the rest of the system. It provides a direct means of
injecting a precise offset to the output. The reference terminal is
also useful when bipolar signals are being amplified as it can be
used to provide a virtual ground voltage. The voltage on the
reference terminal can be varied from –V
S
to +V
S
.
相關PDF資料 |
PDF描述 |
|---|---|
| AD623AR | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| AD623AR-REEL7 | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| AD623ARM | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| AD623ARM-REEL | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| AD623ARM-REEL7 | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD623ANZ | 功能描述:IC AMP INST R-R LP 8DIP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:30pA 電壓 - 輸入偏移:2000µV 電流 - 電源:200µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
| AD623AR | 功能描述:IC AMP INST R-R LP 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:30pA 電壓 - 輸入偏移:2000µV 電流 - 電源:200µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
| AD623AR | 制造商:Analog Devices 功能描述:SEMICONDUCTORS |
| AD623ARM | 制造商:Analog Devices 功能描述:SP Amp INSTR Amp Single R-R O/P 制造商:Analog Devices 功能描述:IC AMP INSTRUMENTATION |
| AD623ARM-REEL | 制造商:Analog Devices 功能描述:SP Amp INSTR Amp Single R-R O/P |
發布緊急采購，3分鐘左右您將得到回復。