- 您現在的位置：買賣IC網 > PDF目錄10979 > AD5933YRSZ (Analog Devices Inc)IC NTWK ANALYZER 12B 1MSP 16SSOP PDF資料下載
參數資料
| 型號： | AD5933YRSZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 25/40頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC NTWK ANALYZER 12B 1MSP 16SSOP |
| 產品培訓模塊： | AD5933 Impedance to Digital Converter Direct Digital Synthesis Tutorial Series (1 of 7): Introduction Direct Digital Synthesizer Tutorial Series (7 of 7): DDS in Action Direct Digital Synthesis Tutorial Series (3 of 7): Angle to Amplitude Converter Direct Digital Synthesis Tutorial Series (6 of 7): SINC Envelope Correction Direct Digital Synthesis Tutorial Series (4 of 7): Digital-to-Analog Converter Direct Digital Synthesis Tutorial Series (2 of 7): The Accumulator |
| 標準包裝： | 1 |
| 分辨率（位）： | 12 b |
| 主 fclk： | 16.776MHz |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 16-SSOP |
| 包裝： | 管件 |
| 產品目錄頁面： | 797 (CN2011-ZH PDF) |
| 配用： | EVAL-AD5933EBZ-ND - BOARD EVALUATION FOR AD5933 |
| 其它名稱： | AD5933BRSZ-ND Q2204656A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
Data Sheet
AD5933
Rev. E | Page 31 of 40
The key point is that the output impedance of the external
has a far less significant effect on gain factor calibration and
subsequent impedance readings in comparison to connecting
the small impedance directly to the VOUT pin (and directly in
series with ROUT). The external amplifier buffers the unknown
impedance from the effects of ROUT and introduces a smaller
output impedance in series with ZUNKNOWN.
For example, if the user measures ZUNKNOWN that is known to
have a small impedance value within the range of 90 Ω to
110 Ω over the frequency range of 30 kHz to 32 kHz, the
user may not be in a position to measure ROUT directly in
the factory/lab. Therefore, the user may choose to add on
an extra amplifier circuit like that shown in Figure 35 to the
signal path of the AD5933. The user must ensure that the
chosen external amplifier has a sufficiently low output series
resistance over the bandwidth of interest in comparison to the
impedance range under test (for an op amp selection guide, see
www.analog.com/opamps). Most amplifiers from Analog
Devices have a curve of closed loop output impedance vs.
frequency at different amplifier gains to determine the output
series impedance at the frequency of interest.
The system settings are
VDD = 3.3 V
VOUT = 2 V p-p
R2 = 20 kΩ
R1 = 4 kΩ
Gain setting resistor = 500
ZUNKNOWN = 100
PGA setting = ×1
To attenuate the excitation voltage at VOUT, choose a ratio
of R1/R2. With the values of R1 = 4 kΩ and R2 = 20 kΩ,
attenuate the signal by 1/5th of 2 V p-p = 400 mV. The
maximum current flowing through the impedance is 400 mV/
90 Ω = 4.4 mA.
The system is subsequently calibrated using the usual method
with a midpoint impedance value of 100 Ω, a calibration
resistor, and a feedback resistor at a midfrequency point in the
sweep. The dynamic range of the input signal to the receive side
of the AD5933 can be improved by increasing the value of the
I-V gain resistor at the RFB pin. For example, increasing the I-V
gain setting resistor at the RFB pin increases the peak-to-peak
signal presented to the ADC input from 400 mV (RFB = 100 Ω)
to 2 V p-p (RFB = 500 Ω).
The gain factor calculated is for a 100 Ω resistor connected
between VOUT and VIN, assuming the output series resistance
of the external amplifier is small enough to be ignored.
When biasing the circuit shown in Figure 35, note that the
receive side of the AD5933 is hard-biased about VDD/2 by
design. Therefore, to prevent the output of the external
amplifier (attenuated AD5933 Range 1 excitation signal) from
saturating the receive side amplifiers of the AD5933, a voltage
equal to VDD/2 must be applied to the noninverting terminal
of the external amplifier.
相關PDF資料 |
PDF描述 |
|---|---|
| MC908JL3EMPE | IC MCU 4K FLASH W/OSC 28-PDIP |
| MC908AP8CFAE | IC MCU 8K FLASH 8MHZ 48-LQFP |
| AD9851BRSZ | IC SYNTHESIZER DDS/DAC 28-SSOP |
| S9S08DZ96F2MLF | MCU 96K FLASH MASK AUTO 48-LQFP |
| AD9850BRSZ | IC DDS SYNTHESIZER CMOS 28-SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5933YRSZ | 制造商:Analog Devices 功能描述:IC IMPEDANCE CONV 1MSPS 12BIT 16SSOP |
| AD5933YRSZ-REEL7 | 功能描述:NETWORK ANALYZER 12B 1MSP 16SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 直接數字合成 (DDS) 系列:- 產品變化通告:Product Discontinuance 27/Oct/2011 標準包裝:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 調節字寬（位）:32 b 電源電壓:2.97 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AD5934 | 制造商:Analog Devices 功能描述:IMPEDANCE TO DIGITAL CONVERTERS - Bulk |
| AD5934YRSZ | 功能描述:IC NTWK ANALYZER 12B 1MSP 16SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 直接數字合成 (DDS) 系列:- 產品變化通告:Product Discontinuance 27/Oct/2011 標準包裝:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 調節字寬（位）:32 b 電源電壓:2.97 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AD5934YRSZ-REEL7 | 功能描述:IC CONV 12BIT 250KSPS 16SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 直接數字合成 (DDS) 系列:- 產品變化通告:Product Discontinuance 27/Oct/2011 標準包裝:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 調節字寬（位）:32 b 電源電壓:2.97 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。