- 您現在的位置：買賣IC網 > PDF目錄375234 > AD586 (Analog Devices, Inc.) High Precision 5 V Reference(高精度5V電壓基準) PDF資料下載
參數資料
| 型號： | AD586 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | High Precision 5 V Reference(高精度5V電壓基準) |
| 中文描述： | 高精度5 V參考（高精度5V的電壓基準） |
| 文件頁數： | 4/8頁 |
| 文件大?。?/td> | 211K |
| 代理商： | AD586 |
AD586
REV. C
–4–
T HE ORY OF OPE RAT ION
T he AD586 consists of a proprietary buried Zener diode refer-
ence, an amplifier to buffer the output and several high stability
thin-film resistors as shown in the block diagram in Figure 1.
T his design results in a high precision monolithic 5 V output
reference with initial offset of 2.0 mV or less. T he temperature
compensation circuitry provides the device with a temperature
coefficient of under 2 ppm/
°
C.
Using the bias compensation resistor between the Zener output
and the noninverting input to the amplifier, a capacitor can be
added at the NOISE REDUCT ION pin (Pin 8) to form a low-
pass filter and reduce the noise contribution of the Zener to the
circuit.
Figure 1. AD586 Functional Block Diagram
APPLY ING T HE AD586
T he AD586 is simple to use in virtually all precision reference
applications. When power is applied to Pin 2 and Pin 4 is
grounded, Pin 6 provides a 5 V output. No external components
are required; the degree of desired absolute accuracy is achieved
simply by selecting the required device grade. T he AD586 re-
quires less than 3 mA quiescent current from an operating sup-
ply of +12 V or +15 V.
An external fine trim may be desired to set the output level to
exactly 5.000 V (calibrated to a main system reference). System
calibration may also require a reference voltage that is slightly
different from 5.000 V, for example, 5.12 V for binary applica-
tions. In either case, the optional trim circuit shown in Figure 2
can offset the output by as much as 300 mV, if desired, with
minimal effect on other device characteristics.
Figure 2. Optional Fine Trim Configuration
NOISE PE RFORMANCE AND RE DUCT ION
T he noise generated by the AD586 is typically less than 4
μ
V
p-p over the 0.1 Hz to 10 Hz band. Noise in a 1 MHz band-
width is approximately 200
μ
V p-p. T he dominant source of this
noise is the buried Zener which contributes approximately
100 nV/
√
Hz
. In comparison, the op amp’s contribution is negli-
gible. Figure 3 shows the 0.1 Hz to 10 Hz noise of a typical
AD586. T he noise measurement is made with a bandpass filter
made of a 1-pole high-pass filter with a corner frequency at
0.1 Hz and a 2-pole low-pass filter with a corner frequency at
12.6 Hz to create a filter with a 9.922 Hz bandwidth.
If further noise reduction is desired, an external capacitor may
be added between the NOISE REDUCT ION pin and ground as
shown in Figure 2. T his capacitor, combined with the 4 k
R
S
and the Zener resistances form a low-pass filter on the output of
the Zener cell. A 1
μ
F capacitor will have a 3 dB point at 12 Hz,
and it will reduce the high frequency (to 1 MHz) noise to about
160
μ
V p-p. Figure 4 shows the 1 MHz noise of a typical AD586
both with and without a 1
μ
F capacitor.
Figure 3. 0.1 Hz to 10 Hz Noise
Figure 4. Effect of 1
μ
F Noise Reduction Capacitor on
Broadband Noise
T URN-ON T IME
Upon application of power (cold start), the time required for the
output voltage to reach its final value within a specified error
band is defined as the turn-on settling time. T wo components
normally associated with this are: the time for the active circuits
to settle, and the time for the thermal gradients on the chip to
stabilize. Figure 5 shows the turn-on characteristics of the
AD586. It shows the settling to be about 60
μ
sec to 0.01%.
Note the absence of any thermal tails when the horizontal scale
is expanded to l ms/cm in Figure 5b.
相關PDF資料 |
PDF描述 |
|---|---|
| AD590 | Two-Terminal IC Temperature Transducer(兩端口溫度傳感器) |
| AD5930 | Programmable Frequency Sweep and Output Burst Waveform Generator |
| AD5930YRUZ | Programmable Frequency Sweep and Output Burst Waveform Generator |
| AD5930YRUZ-REEL7 | Programmable Frequency Sweep and Output Burst Waveform Generator |
| AD598 | LVDT Signal Conditioner(線性可變差分變壓器信號調節器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD586_05 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Precision 5 V Reference |
| AD586A | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Precision 5 V Reference |
| AD586AR | 功能描述:IC VREF SERIES PREC 5V 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:- 標準包裝:2,000 系列:- 基準類型:旁路，可調節，精度 輸出電壓:1.24 V ~ 16 V 容差:±0.5% 溫度系數:- 輸入電壓:1.24 V ~ 16 V 通道數:1 電流 - 陰極:100µA 電流 - 靜態:- 電流 - 輸出:20mA 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:TO-226-3、TO-92-3（TO-226AA）成形引線 供應商設備封裝:TO-92-3 包裝:帶卷 (TR) |
| AD586AR-REEL | 功能描述:IC VREF SERIES PREC 5V 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:- 標準包裝:2,000 系列:- 基準類型:旁路，可調節，精度 輸出電壓:1.24 V ~ 16 V 容差:±0.5% 溫度系數:- 輸入電壓:1.24 V ~ 16 V 通道數:1 電流 - 陰極:100µA 電流 - 靜態:- 電流 - 輸出:20mA 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:TO-226-3、TO-92-3（TO-226AA）成形引線 供應商設備封裝:TO-92-3 包裝:帶卷 (TR) |
| AD586ARZ | 功能描述:IC VREF SERIES PREC 5V 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:- 標準包裝:2,000 系列:- 基準類型:旁路，可調節，精度 輸出電壓:1.24 V ~ 16 V 容差:±0.5% 溫度系數:- 輸入電壓:1.24 V ~ 16 V 通道數:1 電流 - 陰極:100µA 電流 - 靜態:- 電流 - 輸出:20mA 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:TO-226-3、TO-92-3（TO-226AA）成形引線 供應商設備封裝:TO-92-3 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。