- 您現在的位置：買賣IC網 > PDF目錄373884 > AD5801 (Analog Devices, Inc.) Piezo-Electric Actuator Controller PDF資料下載
參數資料
| 型號： | AD5801 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Piezo-Electric Actuator Controller |
| 中文描述： | 壓電致動器控制器 |
| 文件頁數： | 9/13頁 |
| 文件大?。?/td> | 209K |
| 代理商： | AD5801 |
Preliminary Technical Data
AD5801
programme up to four transitions within the time set in the
PWMPERIOD Register (See Figure 4 for typical timing
diagrams, with outputs FC and FD as an example).
Rev. 0 | Page 9 of 13
The number of PWMPERIOD periods is again set in the
AFSTEPS and ZSTEPS Registers. When the outputs are
disabled they can be set configured in a High Impedance, or
High or Low state.
PWMPERIOD
PWMAFCT1
PWMAFCT2
PWMAFDT1
PWMAFDT2
PWM
FC
PWM
FD
PWMAFCT3
PWMAFCT4
PWMAFDT4
PWMAFDT3
Figure 4. Timing Diagram for PWM Drivers.
Temperature Compensation of Drive Patterns
Because of the high temperature coefficients associated with
piezo elements fine tuning of the drive pattern and drive
frequencies are required to ensure the device operates over its
intended temperature range.
In all drive modes it is possible to specify different timing
parameters for three different temperature areas.. If
Temperature compensation mode is selected by programming
the appropriate bit to the DRIVEMODE register, the PTAT
temperature is checked at the beginning of the new ACTIVE
move command and depending on the Temperature recorded
the timing data for the move is read from the appropriate
timing register, HOT, COLD or NOMINAL.
The timing registers for all the driver outputs FA-ZD are
duplicated for Hot and Cold operation and the relevant timing
information for the Hot and Cold bands of operation are
programmed in these Registers.
PWM Slope Mode
A piezo element is a block of ceramic material and is basically a
moving capacitor. The electrical energy of the drive patterns are
converted into mechanical reaction energy inside the piezo
element, and the resulting deformation in the material is used
to produce forces to move the lens assembly in an optical
module.
Driving a capacitive element with digital patterns may produce
large surges in power because power is only consumed during
transients and the impedance of the piezo motor can be very
small on the rising and falling edges of a pulse.
TheAD5801 has an alternative driving scheme called the PWM
Slope Mode which can be employed on Channels FA and FB.
The Slope Mode allows the user to control the rise and fall
times of the drive waveform by taking advantage of the energy
storage properties of the series inductor and the resultant LC
相關PDF資料 |
PDF描述 |
|---|---|
| AD587JCHIPS | High Precision 10 V Reference |
| AD587JN | High Precision 10 V Reference |
| AD587JR | High Precision 10 V Reference |
| AD587 | High Precision 10 V Reference |
| AD587KN | High Precision 10 V Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5801BCBZ-REEL | 制造商:Analog Devices 功能描述:8-CH LENS DRIVER - Tape and Reel |
| AD5801BCBZ-REEL7 | 制造商:Analog Devices 功能描述:8-CH LENS DRIVER - Tape and Reel |
| AD5801BCPZ-REEL | 制造商:Analog Devices 功能描述:8-CH LENS DRIVER - Tape and Reel |
| AD5801BCPZ-REEL7 | 功能描述:IC LENS DRIVER 9-CHAN 32-LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| AD5805BCBZ-REEL | 功能描述:IC LENS DRIVER 32-LFCSP 制造商:analog devices inc. 系列:* 零件狀態:上次購買時間 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。