- 您現在的位置：買賣IC網 > PDF目錄373883 > AD5620ARJ-2500RL7 (ANALOG DEVICES INC) Single, 12-/14-/16-Bit nanoDAC with 5 ppm/C On-Chip Reference in SOT-23 PDF資料下載
參數資料
| 型號： | AD5620ARJ-2500RL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | DAC |
| 英文描述： | Single, 12-/14-/16-Bit nanoDAC with 5 ppm/C On-Chip Reference in SOT-23 |
| 中文描述： | SERIAL INPUT LOADING, 8 us SETTLING TIME, 12-BIT DAC, PDSO8 |
| 封裝： | MO-178BA, SOT-23, 8 PIN |
| 文件頁數： | 17/24頁 |
| 文件大?。?/td> | 558K |
| 代理商： | AD5620ARJ-2500RL7 |
AD5620/AD5640/AD5660
THEORY OF OPERATION
D/A SECTION
The AD5620/AD5640/AD5660 DACs are fabricated on a CMOS
process. The architecture consists of a string DAC followed by an
output buffer amplifier. The parts include an internal 1.25 V/2.5 V,
5 ppm/°C reference that is internally gained up by 2. Figure 38
shows a block diagram of the DAC architecture.
Rev. A | Page 17 of 24
V
DD
R
R
V
OUT
GND
RESISTOR
STRING
REF (+)
REF (–)
OUTPUT
AMPLIFIER
DAC REGISTER
0
V
FB
Figure 38. DAC Architecture
Because the input coding to the DAC is straight binary, the ideal
output voltage is given by
×
×
=
N
REFOUT
V
OUT
D
2
V
2
where:
D
is the decimal equivalent of the binary code that is loaded to
the DAC register.
0 to 4,095 for AD5620 (12 bit)
0 to 16,383 for AD5640 (14 bit)
0 to 65,535 for AD5660 (16 bit)
N
is the DAC resolution.
R
R
R
R
R
TO OUTPUT
AMPLIFIER
0
Figure 39. Resistor String
RESISTOR STRING
The resistor string section is shown in Figure 39. It is simply a
string of resistors, each of value R. The code loaded to the DAC
register determines at which node on the string the voltage is
tapped off to be fed into the output amplifier. The voltage is
tapped off by closing one of the switches connecting the
string to the amplifier. Because it is a string of resistors, it is
guaranteed monotonic.
INTERNAL REFERENCE
The AD5620/AD5640/AD5660-1 parts include an internal,
1.25 V, 5 ppm/°C reference, giving a full-scale output voltage of
2.5 V. The AD5620/AD5640/AD5660-2-3 parts include an
internal, 2.5 V, 5 ppm/°C reference, giving a full-scale output
voltage of 5 V. The reference associated with each part is
available at the V
REFOUT
pin. A buffer is required if the reference
output is used to drive external loads. It is recommended that a
100 nF capacitor is placed between the reference output and
GND for reference stability.
OUTPUT AMPLIFIER
The output buffer amplifier can generate rail-to-rail voltages on
its output, which gives an output range of 0 V to V
DD
. This output
buffer amplifier has a gain of 2 derived from a 50 kΩ resistor
divider network in the feedback path. The inverting input of the
output amplifier is available to the user, allowing for remote
sensing. This V
FB
pin must be connected to V
OUT
for normal
operation. It can drive a load of 2 kΩ in parallel with 1,000 pF
to GND. Figure 21 shows the source and sink capabilities of the
output amplifier. The slew rate is 1.5 V/μs with a to full-
scale settling time of 10 μs.
SERIAL INTERFACE
The AD5620/AD5640/AD5660 have a 3-wire serial interface
(SYNC, SCLK, and DIN) that is compatible with SPI, QSPI, and
MICROWIRE interface standards as well as most DSPs.
See Figure 2 for a timing diagram of a typical write sequence.
The write sequence begins by bringing the SYNC line low.
Data from the DIN line is clocked into the 16-bit shift register
(AD5620/AD5640) or the 24-bit shift register (AD5660) on the
falling edge of SCLK. The serial clock frequency can be as high
as 30 MHz, making the AD5620/AD5640/AD5660 compatible
with high speed DSPs. On the 16th falling clock edge (AD5620/
AD5640) or the 24th falling clock edge (AD5660), the last data
bit is clocked in and the programmed function is executed, that
is, a change in the DAC register contents and/or a change in the
mode of operation is executed. At this stage, the SYNC line can
be kept low or be brought high. In either case, it must be brought
high for a minimum of 33 ns before the next write sequence so
that a falling edge of SYNC can initiate the next write sequence.
Because the SYNC buffer draws more current when V
IN
= 2 V
than it does when V
IN
= 0.8 V, SYNC should be idled low between
write sequences for even lower power operation of the parts. As
is mentioned previously, however, SYNC must be brought high
again just before the next write sequence.
相關PDF資料 |
PDF描述 |
|---|---|
| AD5620ARJ-2REEL7 | Single, 12-/14-/16-Bit nanoDAC with 5 ppm/C On-Chip Reference in SOT-23 |
| AD5620CRM-3REEL7 | Single, 12-/14-/16-Bit nanoDAC with 5 ppm/C On-Chip Reference in SOT-23 |
| AD5620CRM-1 | Single, 12-/14-/16-Bit nanoDAC with 5 ppm/C On-Chip Reference in SOT-23 |
| AD5620CRM-1REEL7 | Single, 12-/14-/16-Bit nanoDAC with 5 ppm/C On-Chip Reference in SOT-23 |
| AD5620CRM-2 | Single, 12-/14-/16-Bit nanoDAC with 5 ppm/C On-Chip Reference in SOT-23 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5620ARJ-2REEL7 | 功能描述:數模轉換器- DAC Single 12 Bit 5V w/ reference IC RoHS:否 制造商:Analog Devices 轉換器數量:4 DAC 輸出端數量:4 轉換速率: 分辨率:12 bit 接口類型:Serial (I2C) 穩定時間: 最大工作溫度:+ 105 C 安裝風格: 封裝 / 箱體:TSSOP 封裝:Reel |
| AD5620ARJZ-1500RL7 | 功能描述:IC DAC 12BIT SPI/SRL SOT23-8 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:nanoDAC™ 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:3,000 系列:nanoDAC™ 設置時間:80µs 位數:18 數據接口:DSP，MICROWIRE?，QSPI?，串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極 采樣率（每秒）:- 產品目錄頁面:784 (CN2011-ZH PDF) 配用:EVAL-AD5680EBZ-ND - BOARD EVAL FOR AD5680 其它名稱:AD5680BRJZ-2REEL7TR |
| AD5620ARJZ-2500RL7 | 功能描述:IC DAC 12BIT SPI/SRL SOT23-8 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:nanoDAC™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓，單極 采樣率（每秒）:* 產品目錄頁面:1398 (CN2011-ZH PDF) |
| AD5620ARJZ-2REEL7 | 功能描述:IC DAC 12BIT SPI/SRL SOT23-8 RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:nanoDAC™ 產品培訓模塊:Data Converter Fundamentals DAC Architectures 設計資源:Unipolar, Precision DC Digital-to-Analog Conversion using AD5450/1/2/3 8-14-Bit DACs (CN0052) Precision, Bipolar, Configuration for AD5450/1/2/3 8-14bit Multiplying DACs (CN0053) AC Signal Processing Using AD5450/1/2/3 Current Output DACs (CN0054) Programmable Gain Element Using AD5450/1/2/3 Current Output DAC Family (CN0055) Single Supply Low Noise LED Current Source Driver Using a Current Output DAC in the Reverse Mode (CN0139) 標準包裝:10,000 系列:- 設置時間:- 位數:12 數據接口:DSP，MICROWIRE?，QSPI?，串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 薄型，TSOT-23-8 供應商設備封裝:TSOT-23-8 包裝:帶卷 (TR) 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:2.7M |
| AD5620ARMZ-2 | 功能描述:數模轉換器- DAC Single 5V 12bit SPI DAC with reference RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。