- 您現在的位置：買賣IC網 > PDF目錄362093 > AD558TE 8-Bit Digital-to-Analog Converter PDF資料下載
參數資料
| 型號： | AD558TE |
| 英文描述： | 8-Bit Digital-to-Analog Converter |
| 中文描述： | 8位數字到模擬轉換器 |
| 文件頁數： | 4/8頁 |
| 文件大?。?/td> | 334K |
| 代理商： | AD558TE |
AD558
REV. A
–4–
CIRCUIT DESCRIPTION
The AD558 consists of four major functional blocks, fabricated
on a single monolithic chip (see Figure 2). The main D-to-A
converter section uses eight equally-weighted laser-trimmed
current sources switched into a silicon-chromium thin-film
R/2R resistor ladder network to give a direct but unbuffered 0
mV to 400 mV output range. The transistors that form the
DAC switches are PNPs; this allows direct positive-voltage logic
interface and a zero-based output range.
CAMP
GAP
REFERENCE
OUTPUT
AMP
8-BIT VOLTAGE-SWITCHING
D-TO-A CONVERTER
I
2
L LATCHES
2
L
COI
LOGIC
V
OUT
V
OUT
V
OUT
SENSE
SELECT
+V
CC
MSB
D
CS
CE
LSB
D
CONTROL
INPUTS
D
D
D
D
D
D
DIGITAL INPUT DATA
GND
GND
Figure 2. AD558 Functional Block Diagram
The high speed output buffer amplifier is operated in the non-
inverting mode with gain determined by the user-connections
at the output range select pin. The gain-setting application
resistors are thin-film laser-trimmed to match and track the
DAC resistors and to assure precise initial calibration of the two
output ranges, 0 V to 2.56 V and 0 V to 10 V. The amplifier
output stage is an NPN transistor with passive pull-down for
zero-based output capability with a single power supply. The
internal precision voltage reference is of the patented bandgap
type. This design produces a reference voltage of 1.2 volts and
thus, unlike 6.3 volt temperature compensated Zeners, may be
operated from a single, low voltage logic power supply. The
microprocessor interface logic consists of an 8-bit data latch and
control circuitry. Low power, small geometry and high speed
are advantages of the I
2
L design as applied to this section. I
2
L is
bipolar process compatible so that the performance of the ana-
log sections need not be compromised to provide on-chip logic
capabilities. The control logic allows the latches to be operated
from a decoded microprocessor address and write signal. If the
application does not involve a
μ
P
or data bus, wiring CS and
CE to ground renders the latches “transparent” for direct DAC
access.
MIL-STD-883
The rigors of the military/aerospace environment, temperature
extremes, humidity, mechanical stress, etc., demand the utmost
in electronic circuits. The AD558, with the inherent reliability
of integrated circuit construction, was designed with these ap-
plications in mind. The hermetically-sealed, low profile DIP
package takes up a fraction of the space required by equivalent
modular designs and protects the chip from hazardous environ-
ments. To further ensure reliability, military temperature range
AD558 grades S and T are available screened to MIL-STD-883.
For more complete data sheet information consult the Analog
Devices’ Military Databook.
CHIP AVAILABILITY
The AD558 is available in laser-trimmed, passivated chip form.
AD558J and AD558T chips are available. Consult the factory
for details.
Input Logic Coding
Digital Input Code
Output Voltage
Binary
Hexadecimal Decimal
2.56 V Range 10.000 V Range
0000 0000
0000 0001
0000 0010
0000 1111
0001 0000
0111 1111
1000 0000
1100 0000
1111 1111
00
01
02
0F
10
7F
80
C0
FF
0
1
2
15
16
127
128
192
255
0
0.010 V
0.020 V
0.150 V
0.160 V
1.270 V
1.280 V
1.920 V
2.55 V
0
0.039 V
0.078 V
0.586 V
0.625 V
4.961 V
5.000 V
7.500 V
9.961 V
CONNECTING THE AD558
The AD558 has been configured for ease of application. All ref-
erence, output amplifier and logic connections are made inter-
nally. In addition, all calibration trims are performed at the
factory assuring specified accuracy without user trims. The only
connection decision that must be made by the user is a single
jumper to select output voltage range. Clean circuit board lay-
out is facilitated by isolating all digital bit inputs on one side of
the package; analog outputs are on the opposite side.
Figure 3 shows the two alternative output range connections.
The 0 V to 2.56 V range may be selected for use with any power
supply between +4.5 V and +16.5 V. The 0 V to 10 V range
requires a power supply of +11.4 V to +16.5 V.
OUTPUT
AMP
16
15
14
13
GND
V
OUT
SELECT
V
OUT
SENSE
V
OUT
OUTPUT
AMP
16
15
14
13
GND
V
OUT
SELECT
V
OUT
SENSE
V
OUT
a. 0 V to 2.56 V Output Range b. 0 V to 10 V Output Range
Figure 3. Connection Diagrams
Because of its precise factory calibration, the AD558 is intended
to be operated without user trims for gain and offset; therefore
no provisions have been made for such user trims. If a small in-
crease in scale is required, however, it may be accomplished
by slightly altering the effective gain of the output buffer. A
resistor in series with V
OUT
SENSE will increase the output
range.
For example if a 0 V to 10.24 V output range is desired (40 mV
= 1 LSB), a nominal resistance of 850
is required. It must be
remembered that, although the internal resistors all ratio-
match and track, the
absolute
tolerance of these resistors is
typically
±
20% and the
absolute
TC is typically –50 ppm/
°
C
(0 to –100 ppm/
°
C). That must be considered when rescaling is
performed. Figure 4 shows the recommended circuitry for a
full-scale output range of 10.24 volts. Internal resistance values
shown are nominal.
相關PDF資料 |
PDF描述 |
|---|---|
| AD558JD | DACPORT Low Cost, Complete uP-Compatible 8-Bit DAC |
| AD558JN | DACPORT Low Cost, Complete uP-Compatible 8-Bit DAC |
| AD558JP | DACPORT Low Cost, Complete uP-Compatible 8-Bit DAC |
| AD558J | DACPORT Low Cost, Complete uP-Compatible 8-Bit DAC |
| AD558K | DACPORT Low Cost, Complete uP-Compatible 8-Bit DAC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD558TE/883B | 功能描述:數模轉換器- DAC IC MONO 8-BIT D/A CONVER RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| AD5590 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16 Input, 16 Output Analog I/O Port with Integrated Amplifiers |
| AD5590BBC | 功能描述:IC ADC I/O PORT16 W/AMP 80CSPBGA RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD5590BBCZ | 功能描述:IC ADC I/O PORT-16 AMP 80-CSPBGA RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD5592RBCBZ-1-RL7 | 功能描述:IC DAC/ADC 12BIT OCT SPI 16WLCSP 制造商:analog devices inc. 系列:- 包裝:剪切帶（CT） 零件狀態:在售 類型:ADC，DAC 分辨率（位）:12 b 采樣率（每秒）:400k 數據接口:SPI 電壓源:單電源 電壓 - 電源:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:16-UFBGA，WLCSP 供應商器件封裝:16-WLCSP(1.96x1.96) 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。