參數資料
型號： AD5392BCP-3
廠商： ANALOG DEVICES INC
元件分類： DAC
英文描述： 8-/16-Channel, 3 V/5 V, Serial Input, Single- Supply, 12-/14-Bit Voltage Output DACs
中文描述： SERIAL INPUT LOADING, 8 us SETTLING TIME, 14-BIT DAC, QCC64
封裝： 9 X 9 MM, MO-220VMMD-4, LFCSP-64
文件頁數： 33/44頁
文件大小： 1319K
代理商： AD5392BCP-3
AD5390/AD5391/AD5392
CONTROL REGISTER WRITE
Table 25 shows the control register contents for the AD5390 and the AD5392. Table 26 provides bit descriptions. Note that
REG1 = REG0 = 0, A3–A0 = 1100, and DB13–DB0 contain the control register data.
Table 25. AD5390/AD5392 Control Register Contents
MSB
CR13
CR12
CR11
CR10
CR9
CR8
Rev. A | Page 33 of 44
CR7
CR6
CR5
CR4
CR3
CR2
CR1
LSB
CR0
Table 26. AD5390 and AD5392 Bit Descriptions
Bit
Description
CR13
Power-Down Status. This bit is used to configure the output amplifier state in power–down mode.
CR13 = 1: Amplifier output is high impedance (default on power-up).
CR13 = 0: Amplifier output is 100 k to ground.
CR12
REF Select. This bit selects the operating internal reference for the AD539x. CR12 is programmed as follows:
CR12 = 1: Internal reference is 2.5 V (AD5390/AD5392-5 default). Recommended operating reference for AD539x-5.
CR12 = 0: Internal reference is 1.25 V (AD5390/AD5392-3 default). Recommended operating reference for AD5390-3 and
AD5392-3.
CR11
Current Boost Control. This bit is used to boost the current in the output amplifier, thus altering its slew rate and is
configured as follows:
CR11 = 1: Boost mode on. This maximizes the bias current in the output amplifier, optimizing its slew rate but increasing
the power dissipation.
CR11 = 0: Boost mode off (default on power-up). This reduces the bias current in the output amplifier and reduces the
overall power consumption.
CR10
Internal/External Reference. This bit determines if the DAC uses its internal reference or an external reference.
CR10 = 1: Internal reference enabled. Reference output depends on data loaded to CR12.
CR10 = 0: External reference selected (default on power-up).
CR9
Channel Monitor Enable (see Table 23).
CR9 = 1: Monitor enabled. This enables the channel monitor function. Following a write to the monitor channel in the SFR
register, the selected channel output is routed to the MON_OUT pin.
CR9 = 0: Monitor disabled (default on power-up). When monitor is disabled, the MON_OUT pin is three-stated.
CR8
Thermal Monitor Function. This function is used to monitor the internal die temperature of the AD5390/AD5392, when
enabled. The thermal monitor powers down the output amplifiers when the temperature exceeds 130°C. This function
can be used to protect the device in cases where the power dissipation of the device may be exceeded, if a number of
output channels are simultaneously short circuited. A soft power-up re-enables the output amplifiers, if the die
temperature has dropped below 130°C.
CR8 = 1: Thermal monitor enabled.
CR8 = 0: Thermal monitor disabled (default on power-up).
CR7 to CR4
Don’t Care.
CR3 to CR2
Toggle Function Enable. This function lets the user toggle the output between two codes loaded to the A and B register
for each DAC. Control Register Bits CR3 and CR2 are used to enable individual groups of eight channels for operation in
toggle mode on the AD5390 and AD5392, as follows:
CR3 Group 1 Channels 8 to 15
CR2 Group 0 Channels 0 to 7
CR2 is the only active bit on the AD5392. Logic 1 written to any bit enables a group of channels, and Logic 0 disables a
group. LDAC is used to toggle between the two registers.
CR1 and CR0
Don’t care.
相關PDF資料
PDF描述
AD5390BCP-5 8-/16-Channel, 3 V/5 V, Serial Input, Single- Supply, 12-/14-Bit Voltage Output DACs
AD5391BCP-5 8-/16-Channel, 3 V/5 V, Serial Input, Single- Supply, 12-/14-Bit Voltage Output DACs
AD5392BCP-5 8-/16-Channel, 3 V/5 V, Serial Input, Single- Supply, 12-/14-Bit Voltage Output DACs
AD5390 8-/16-Channel, 3 V/5 V, Serial Input, Single- Supply, 12-/14-Bit Voltage Output DACs
AD5390BST-3 8-/16-Channel, 3 V/5 V, Serial Input, Single- Supply, 12-/14-Bit Voltage Output DACs
相關代理商/技術參數
參數描述
AD5392BCP-3-REEL7 制造商:Analog Devices 功能描述:DAC 8-CH Resistor-String 14-bit 64-Pin LFCSP EP T/R 制造商:Rochester Electronics LLC 功能描述:8-CHN 3V SINGLE SUPPLY 14-BIT VOUT I.C. - Tape and Reel
AD5392BCP-5 制造商:Analog Devices 功能描述:DAC 8-CH Resistor-String 14-bit 64-Pin LFCSP EP 制造商:Analog Devices 功能描述:14BIT DAC 8CH 5V 5392 LFCSP-64
AD5392BCP-5-REEL 制造商:Analog Devices 功能描述:DAC 8-CH Resistor-String 14-bit 64-Pin LFCSP EP T/R
AD5392BCP-5-REEL7 制造商:Analog Devices 功能描述:DAC 8-CH Resistor-String 14-bit 64-Pin LFCSP EP T/R
AD5392BCPZ-3 功能描述:IC DAC 14BIT 8CHAN 3V 64LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散（最大）:100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC（J 形引線） 供應商設備封裝:28-PLCC（11.51x11.51） 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:143k
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*