- 您現在的位置：買賣IC網 > PDF目錄373878 > AD5382BST-3-REEL (ANALOG DEVICES INC) CONNECTOR ACCESSORY PDF資料下載
參數資料
| 型號： | AD5382BST-3-REEL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | DAC |
| 英文描述： | CONNECTOR ACCESSORY |
| 中文描述： | PARALLEL, WORD INPUT LOADING, 8 us SETTLING TIME, 14-BIT DAC, PQFP100 |
| 封裝： | 14 X 14 MM, MS-026BED, LQFP-100 |
| 文件頁數： | 25/40頁 |
| 文件大?。?/td> | 616K |
| 代理商： | AD5382BST-3-REEL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
AD5382
HARDWARE FUNCTIONS
RESET FUNCTION
Bringing the RESET line low resets the contents of all internal
registers to their power-on reset state. Reset is a negative edge-
sensitive input. The default corresponds to m at full scale and to
c at zero. The contents of the DAC registers are cleared, setting
VOUT 0 to VOUT 31 to 0 V. This sequence takes 270 μs max.
The falling edge of RESET initiates the reset process; BUSY goes
low for the duration, returning high when RESET is complete.
While BUSY is low, all interfaces are disabled and all LDAC
pulses are ignored. When BUSY returns high, the part resumes
normal operation and the status of the RESET pin is ignored
until the next falling edge is detected.
Rev. 0 | Page 25 of 40
ASYNCHRONOUS CLEAR FUNCTION
Bringing the CLR line low clears the contents of the DAC
registers to the data contained in the user configurable CLR
register and sets VOUT 0 to VOUT 31 accordingly. This func-
tion can be used in system calibration to load zero scale and full
scale to all channels. The execution time for a CLR is 35 μs.
BUSY AND LDAC FUNCTIONS
BUSY is a digital CMOS output that indicates the status of the
AD5382. The value of x2, the internal data loaded to the DAC
data register, is calculated each time the user writes new data to
the corresponding x1, c, or m registers. During the calculation
of x2, the BUSY output goes low. While BUSY is low, the user
can continue writing new data to the x1, m, or c registers, but no
DAC output updates can take place. The DAC outputs are
updated by taking the LDAC input low. If LDAC goes low while
BUSY is active, the LDAC event is stored and the DAC outputs
update immediately after BUSY goes high. The user may hold
the LDAC input permanently low, in which case the DAC
outputs update immediately after BUSY goes high. BUSY also
goes low during power-on reset and when a falling edge is
detected on the RESET pin. During this time, all interfaces are
disabled and any events on LDAC are ignored. The AD5382
contains an extra feature whereby a DAC register is not updated
unless its x2 register has been written to since the last time
LDAC was brought low. Normally, when LDAC is brought low,
the DAC registers are filled with the contents of the x2 registers.
However, the AD5382 will only update the DAC register if the
x2 data has changed, thereby removing unnecessary digital
crosstalk.
FIFO OPERATION IN PARALLEL MODE
The AD5382 contains a FIFO to optimize operation when
operating in parallel interface mode. The FIFO Enable (level
sensitive, active high) is used to enable the internal FIFO. When
connected to DVDD, the internal FIFO is enabled, allowing the
user to write to the device at full speed. FIFO is only available in
parallel interface mode. The status of the FIFO_EN pin is
sampled on power-up, and after a CLEAR or RESET, to
determine if the FIFO is enabled. In either serial or I
2
C interface
modes, FIFO_EN should be tied low. Up to 128 successive
instructions can be written to the FIFO at maximum speed in
parallel mode. When the FIFO is full, any further writes to the
device are ignored. Figure 29 shows a comparison between
FIFO mode and non-FIFO mode in terms of channel update
time. Figure 29 also outlines digital loading time.
NUMBER OF WRITES
T
μ
s
1
4
7
10
13
16
19
22
25
28
31
34
37
0
10
5
15
25
20
40
WITHOUT FIFO
(CHANNEL UPDATE TIME)
WITH FIFO
(CHANNEL UPDATE TIME)
WITH FIFO
(DIGITAL LOADING TIME)
0
Figure 29. Channel Update Rate (FIFO vs. NON-FIFO)
POWER-ON RESET
The AD5382 contains a power-on reset generator and state
machine. The power-on reset resets all registers to a predefined
state and configures the analog outputs as high impedance. The
BUSY pin goes low during the power-on reset sequencing,
preventing data writes to the device.
POWER-DOWN
The AD5382 contains a global power-down feature that puts all
channels into a low power mode and reduces the analog power
consumption to 2 μA max and digital power consumption to
20 μA max. In power-down mode, the output amplifier can be
configured as a high impedance output or provide a 100 k
load to ground. The contents of all internal registers are
retained in power-down mode. When exiting power-down, the
settling time of the amplifier will elapse before the outputs settle
to their correct values.
相關PDF資料 |
PDF描述 |
|---|---|
| AD5382 | 32-Channel, 3 V/5 V, Single-Supply, 14-Bit, Voltage Output DAC |
| AD5382BST-3 | 32-Channel, 3 V/5 V, Single-Supply, 14-Bit, Voltage Output DAC |
| AD5382BST-5 | 32-Channel, 3 V/5 V, Single-Supply, 14-Bit, Voltage Output DAC |
| AD5382BST-5-REEL | 32-Channel, 3 V/5 V, Single-Supply, 14-Bit, Voltage Output DAC |
| AD5383BST-3 | 32-Channel, 3 V/5 V, Single-Supply, 14-Bit, Voltage Output DAC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5382BST-5 | 制造商:Analog Devices 功能描述:DAC 32-CH Resistor-String 14-bit 100-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:32-CHN 5V SINGLE SUPPLY 14-BIT VOUT I.C. - Bulk |
| AD5382BST-5-REEL | 制造商:Analog Devices 功能描述:DAC 32-CH Resistor-String 14-bit 100-Pin LQFP T/R |
| AD5382BSTZ-3 | 功能描述:IC DAC 14BIT 32CHAN 3V 100LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD5382BSTZ-5 | 功能描述:IC DAC 14BIT 32CH 5V 100-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD5383BST | 制造商:Analog Devices 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。