The nomina" />
參數資料
型號： AD5271BCPZ-100-RL7
廠商： Analog Devices Inc
文件頁數： 15/24頁
文件大?。?/td> 0K
描述： IC RHEOSTAT 5V 50-TP 256 10MSOP
標準包裝： 1
接片： 256
電阻（歐姆）： 100k
電路數： 1
溫度系數： 標準值 5 ppm/°C
存儲器類型： 非易失
接口： 4 線串行
電源電壓： 2.7 V ~ 5.5 V，±2.5 V ~ 2.75 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 10-TFSOP，10-MSOP（0.118"，3.00mm 寬）
供應商設備封裝： 10-MSOP
包裝： 標準包裝
其它名稱： AD5271BCPZ-100-RL7DKR
AD5270/AD5271
Data Sheet
Rev. F | Page 22 of 24
PROGRAMMING THE VARIABLE RESISTOR
Rheostat Operation—1% Resistor Tolerance
The nominal resistance between Terminal W and Terminal A, RWA,
is 20 kΩ, 50 kΩ, or 100 kΩ and has 1024-/256-tap points accessed
by the wiper terminal. The 10-/8-bit data in the RDAC latch is
decoded to select one of the 1024 or 256 possible wiper settings.
The AD5270 and AD5271 contain an internal ±1% resistor
tolerance calibration feature that can be disabled or enabled,
enabled by default, or by programming Bit C2 of the control
The digitally programmed output resistance between the W
terminal and the A terminal, RWA, is calibrated to give a
maximum of ±1% absolute resistance error over both the full
supply and temperature ranges. As a result, the general
equations for determining the digitally programmed output
resistance between the W terminal and the A terminal are the
following:
For the AD5270
WA
R
D
R
1024
)
(
(1)
For the AD5271
WA
R
D
R
256
)
(
(2)
where:
D
is the decimal equivalent of the binary code loaded in the
10-/8-bit RDAC register.
RWA
is the end-to-end resistance.
In the zero-scale condition, a finite total wiper resistance of
120 Ω is present. Regardless of which setting the part is oper-
ating in, take care to limit the current between Terminal A to
Terminal W to the maximum continuous current of ±3 mA or
a pulse current specified in Table 8. Otherwise, degradation or
possible destruction of the internal switch contact can occur.
EXT_CAP CAPACITOR
A 1 μF capacitor to VSS must be connected to the EXT_CAP
pin, as shown in Figure 46, on power-up and throughout the
operation of the AD5270/AD5271.
AD5270/
AD5271
50_OTP
MEMORY
BLOCK
EXT_CAP
C1
1F
VSS
08
077
-00
8
Figure 46. EXT_CAP Hardware Setup
TERMINAL VOLTAGE OPERATING RANGE
The positive VDD and negative VSS power supplies of the
AD5270/AD5271 define the boundary conditions for proper
2-terminal digital resistor operation. Supply signals present on
Terminal A and Terminal W that exceed VDD or VSS are clamped
by the internal forward-biased diodes, see Figure 47.
VSS
VDD
A
W
08
077
-00
9
Figure 47. Maximum Terminal Voltages Set by VDD and VSS
The ground pins of the AD5270/AD5271 devices are primarily
used as digital ground references. To minimize the digital ground
bounce, join the AD5270/AD5271 ground terminal remotely
to the common ground. The digital input control signals to the
AD5270/AD5271 must be referenced to the device ground pin
(GND), and must satisfy the logic level defined in the
Specifications section. An internal level shift circuit ensures that
the common-mode voltage range of the three terminals extends
from VSS to VDD, regardless of the digital input level.
POWER-UP SEQUENCE
Because there are diodes to limit the voltage compliance at
Terminal A and Terminal W (see Figure 47), it is important to
power VDD/VSS first before applying any voltage to Terminal A
and Terminal W; otherwise, the diode is forward-biased such
that VDD/VSS are powered unintentionally. The ideal power-up
sequence is VSS, GND, VDD, digital inputs, VA, and VW. The
order of powering VA, VW, and the digital inputs is not
important as long as they are powered after VDD/VSS.
As soon as VDD is powered, the power-on preset activates which
first sets the RDAC to midscale and then restores the last pro-
grammed 50-TP value to the RDAC register.
相關PDF資料
PDF描述
VE-2NB-MY-F1 CONVERTER MOD DC/DC 95V 50W
VE-26P-MY-F4 CONVERTER MOD DC/DC 13.8V 50W
VI-B40-IU-F3 CONVERTER MOD DC/DC 5V 200W
VI-BWM-MV CONVERTER MOD DC/DC 10V 150W
VI-B40-IU-F2 CONVERTER MOD DC/DC 5V 200W
相關代理商/技術參數
參數描述
AD5271BCPZ-20-RL7 功能描述:IC RHEOSTAT 5V 50-TP 256 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR)
AD5271BRMZ-100 功能描述:IC RHEOSTAT 5V 50-TP 256 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR)
AD5271BRMZ-100-RL7 功能描述:DIGITAL POT 256POS 100K SINGLE RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR)
AD5271BRMZ-20 功能描述:IC DGTL POT 20K 256POS 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 35 ppm/°C 存儲器類型:非易失 接口:3 線串口 電源電壓:2.7 V ~ 5.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN-EP（3x3） 包裝:剪切帶 (CT) 產品目錄頁面:1399 (CN2011-ZH PDF) 其它名稱:MAX5423ETA+TCT
AD5271BRMZ-20 制造商:Analog Devices 功能描述:Digital Potentiometer IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*