- 您現在的位置：買賣IC網 > PDF目錄8981 > AD5063BRMZ (Analog Devices Inc)IC DAC 16BIT 2.7-5.5V 10-MSOP PDF資料下載
參數資料
| 型號： | AD5063BRMZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 5/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 16BIT 2.7-5.5V 10-MSOP |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 標準包裝： | 50 |
| 系列： | nanoDAC™ |
| 設置時間： | 4µs |
| 位數： | 16 |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 管件 |
| 輸出數目和類型： | 1 電壓，單極；1 電壓，雙極 |
| 采樣率（每秒）： | 333k |
| 產品目錄頁面： | 781 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
AD5063
Rev. C | Page 13 of
20
THEORY OF OPERATION
The AD5063 is a single 16-bit, serial input, voltage-output DAC.
It operates from supply voltages of 2.7 V to 5.5 V. Data is
written to the AD5063 in a 24-bit word format via a 3-wire serial
interface.
The AD5063 incorporates a power-on reset circuit that ensures
the DAC output powers up to midscale. The device also has a
software power-down mode pin that reduces the typical current
consumption to less than 1 μA.
DAC ARCHITECTURE
The DAC architecture of the AD5063 consists of two matched
DAC sections. A simplified circuit diagram is shown in
Figure 27. The four MSBs of the 16-bit data-word are decoded
to drive 15 switches, E1 to E15. Each of these switches connects
one of 15 matched resistors to either the DACGND or VREF
buffer output. The remaining 12 bits of the data-word drive
Switches S0 to S11 of a 12-bit voltage mode R-2R ladder
network.
2R
0
4
76
6-
02
7
S0
VREF
2R
S1
2R
S11
2R
E1
2R
E2
2R
E15
2R
VOUT
12-BIT R-2R LADDER
FOUR MSBs DECODED INTO
15 EQUAL SEGMENTS
Figure 27. DAC Ladder Structure
REFERENCE BUFFER
The AD5063 operates with an external reference. The reference
input (VREF) has an input range of 2 V to AVDD 50 mV. This
input voltage is used to provide a buffered reference for the
DAC core.
SERIAL INTERFACE
The AD5063 has a 3-wire serial interface (SYNC, SCLK, and
DIN) that is compatible with SPI, QSPI, and MICROWIRE
interface standards, as well as most DSPs. (See
for a
timing diagram of a typical write sequence.)
The write sequence begins by bringing the SYNC line low. Data
from the DIN line is clocked into the 24-bit shift register on the
falling edge of SCLK. The serial clock frequency can be as high
as 30 MHz, making these parts compatible with high speed
DSPs. On the 24th falling clock edge, the last data bit is clocked
in and the programmed function is executed (that is, a change
in the DAC register contents and/or a change in the mode of
operation).
At this stage, the SYNC line can be kept low or be brought
high. In either case, it must be brought high for a minimum of
12 ns before the next write sequence, so that a falling edge of
SYNC can initiate the next write sequence. Because the SYNC
buffer draws more current when VIH = 1.8 V than it does when
VIH = 0.8 V, SYNC should be idled low between write sequences
for even lower power operation of the part. As previously indi-
cated, however, it must be brought high again just before the
next write sequence.
INPUT SHIFT REGISTER
The input shift register is 24 bits wide (see Figure 28). PD1
and PD0 are bits that control the operating mode of the part
(normal mode or any one of the three power-down modes).
There is a more complete description of the various modes in
the Power-Down Modes section. The next 16 bits are the data
bits. These are transferred to the DAC register on the 24th falling
edge of SCLK.
SYNC INTERRUPT
In a normal write sequence, the SYNC line is kept low for at
least 24 falling edges of SCLK, and the DAC is updated on the
24th falling edge. However, if SYNC is brought high before the
24th falling edge, it acts as an interrupt to the write sequence.
The shift register is reset and the write sequence is seen as
invalid. Neither an update of the DAC register contents nor a
change in the operating mode occurs (see
).
DATA BITS
DB15 (MSB)
DB0 (LSB)
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
NORMAL OPERATION
1k TO GND
100k TO GND
THREE-STATE
POWER-DOWN MODES
0
1
0
1
0
1
04
766-
028
00
0
PD1
PD0
Figure 28. Input Register Contents
相關PDF資料 |
PDF描述 |
|---|---|
| AD5063BRMZ-1 | IC DAC 16BIT 2.7-5.5V 10MSOP |
| VE-J0P-MZ-F4 | CONVERTER MOD DC/DC 13.8V 25W |
| VI-B0T-MY-F2 | CONVERTER MOD DC/DC 6.5V 50W |
| AD5722RBREZ | IC DAC DUAL 12BIT 1LSB 24TSSOP |
| AD8300ARZ | IC DAC 12BIT 3V SRL-IN 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5063BRMZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Fully Accurate 16-Bit VOUT nanoDAC SPI Interface 2.7 V to 5.5 V in an MSOP |
| AD5063BRMZ-1 | 功能描述:IC DAC 16BIT 2.7-5.5V 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:nanoDAC™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓，單極 采樣率（每秒）:* 產品目錄頁面:1398 (CN2011-ZH PDF) |
| AD5063BRMZ-11 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Fully Accurate 16-Bit VOUT nanoDAC SPI Interface 2.7 V to 5.5 V in an MSOP |
| AD5063BRMZ-1-REEL7 | 功能描述:IC DAC 16BIT 2.7-5.5V 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:nanoDAC™ 標準包裝:47 系列:- 設置時間:2µs 位數:14 數據接口:并聯 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:55µW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:管件 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:* |
| AD5063BRMZ-1-REEL71 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Fully Accurate 16-Bit VOUT nanoDAC SPI Interface 2.7 V to 5.5 V in an MSOP |
發布緊急采購，3分鐘左右您將得到回復。