參數資料
型號： ACT-700SC-150F24Q
英文描述： Microprocessor
中文描述： 微處理器
文件頁數： 15/24頁
文件大?。?/td> 227K
代理商： ACT-700SC-150F24Q
Aeroflex Circuit Technology
SCD7000 REV A 3/16/00 Plainview NY (516) 694-6700
15
level registers are located in the coprocessor 0 control
register space. For further details about the control
space see the section describing coprocessor 0.
In addition to programmable priority levels, the ACT
7000SC also permits the spacing between interrupt
vectors to be programmed. For example, the
minimum spacing between two adjacent vectors is
0x20
while
the
maximum
programmability allows the user to either set up the
vectors as jumps to the actual interrupt routines or, if
interrupt latency is paramount, to include the entire
interrupt routine at the vector. Table 15 illustrates the
complete set of vector spacing selections along with
the coding as required in the Interrupt Control register
bits 4:0.
In general, the active interrupt priority combined
with the spacing setting generates a vector offset
which is then added to the interrupt base address of
0x200 to generate the interrupt exception offset. This
offset is then added to the exception base to produce
the final interrupt vector address.
Table 15 – Interrupt Vector Spacing
is
0x200.
This
Standby Mode
The ACT 7000SC provides a means to reduce the
amount of power consumed by the internal core when
the CPU would not otherwise be performing any
useful operations. This state is known as Standby
Mode.
Executing the WAIT instruction enables interrupts
and enters Standby Mode. When the WAIT instruction
completes the W pipe stage, if the SysAD bus is
currently idle, the internal processor clocks will stop
thereby freezing the pipeline. The phase lock loop, or
PLL, internal timer/ counter, and the “wake up” input
pins:
IP[5:0]
*,
NMI
*,
ColdReset*
continue to operate in their normal
fashion. If the SysAD bus is not idle when the WAIT
instruction completes the W pipe stage, then the
WAIT is treated as a NOP. Once the processor is in
Standby, any interrupt, including the internally
generated timer interrupt, will cause the processor to
exit Standby and resume operation where it left off.
The
WAIT
instruction is typically inserted in the idle
loop of the operating system or real time executive.
JTAG Interface
The ACT 7000SC interface supports JTAG
boundary scan in conformance with IEEE 1149.1. The
JTAG interface is especially helpful for checking the
integrity of the processor’s pin connections.
Boot-Time Options
Fundamental operational modes for the processor
are initialized by the boot-time mode control interface.
The boot-time mode control interface is a serial
interface operating at a very low frequency
(SysClock
divided by 256). The low frequency
operation allows the initialization information to be
ExtReq
*,
Reset
*,
and
ICR[4..0]
Spacing
0x0
0x1
0x2
0x4
0x8
0x10
others
0x000
0x020
0x040
0x080
0x100
0x200
reserved
Table 11 – Cause Register
31
30
29,28
27
26
25
24
23..8
7
6..2
0,1
BD
0
CE
0
W2
W1
IV
IP[15..0]
0
EXC
0
Table 12 – Interupt Control Register
31..16
15..8
7
6..5
4..00
0
IM[15..8]
TE
0
Spacing
Table 13 – IPLLO Register
31..28
27..24
23..20
19..16
15..12
11..8
7..4
3..0
IPL7
IIPL6
IPL5
IPL4
IPL3
IPL2
IPL1
IPL0
Table 14 – IPLHI Register
31..28
27..24
23..20
19..16
15..12
11..8
7..4
3..0
0
0
IPL13
IPL12
IPL11
IPL10
IPL9
IPL8
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料
PDF描述
ACT-700SC-150F24T Microprocessor
ACT-700SC-200F17C Microprocessor
ACT-700SC-200F17I Microprocessor
ACT-700SC-200F17M Microprocessor
ACT-700SC-200F17Q Microprocessor
相關代理商/技術參數
參數描述
ACT-700SC-150F24T 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microprocessor
ACT-700SC-200F17C 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microprocessor
ACT-700SC-200F17I 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microprocessor
ACT-700SC-200F17M 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microprocessor
ACT-700SC-200F17Q 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microprocessor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*