- 您現在的位置：買賣IC網 > PDF目錄381232 > AAT2550 (Advanced Analog Technology,lnc.) Total Power Solution for Portable Applications PDF資料下載
參數資料
| 型號： | AAT2550 |
| 廠商： | Advanced Analog Technology,lnc. |
| 英文描述： | Total Power Solution for Portable Applications |
| 中文描述： | 總功率便攜式應用解決方案 |
| 文件頁數： | 19/35頁 |
| 文件大?。?/td> | 914K |
| 代理商： | AAT2550 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
used NTC thermistors in battery packs are approx-
imately 10k
Ω
at room temperature (25°C).
The TS pin has been specifically designed to
source 80μA of current to the thermistor. The volt-
age on the TS pin that results from the resistive
load should stay within a window from 330mV to
2.3V. If the battery becomes too hot during charg-
ing due to an internal fault, the thermistor will heat
up and reduce in value, pulling the TS pin voltage
lower than the TS1 threshold, and the AAT2550 will
signal the fault condition.
If the use of the TS pin function is not required by
the system, it should be terminated to ground with
a 10k
Ω
resistor.
Battery Charge Status Indication
The AAT2550 indicates the status of the battery
under charge with two different systems. First, the
device has two status LED driver outputs. These
two LEDs can indicate simple functions such as no
battery charge activity, battery charging, charge
complete, and charge fault. The AAT2550 also pro-
vides a bi-directional data reporting function so that
a system microcontroller can interrogate the DATA
pin and read any one of 13 system states.
Status Indicator Display
Simple system charging status states can be dis-
played using one or two LEDs in conjunction with the
STAT1 and STAT2 pins on the AAT2550. These two
pins are simple switches to connect the LED cath-
odes to ground. It is not necessary to use both dis-
play LEDs if a user simply wants to have a single
lamp to show "charging" or "not charging." This can
be accomplished by using the STAT1 pin and a sin-
gle LED. Using two LEDs and both STAT pins simply
gives the user more information to the charging
states. Refer to Table 3 for LED display definitions.
The LED anodes should be connected to ADP. The
LEDs should be biased with as little current as nec-
essary to create reasonable illumination; therefore,
a ballast resistor should be placed between the
LED cathodes and the STAT1/2 pins. LED current
consumption will add to the overall thermal power
budget for the device package, so it is wise to keep
the LED drive current to a minimum. 2mA should
be sufficient to drive most low-cost green or red
LEDs. It is not recommended to exceed 8mA for
driving an individual status LED.
The required ballast resistor value can be estimat-
ed using the following formulas:
For connection to the adapter supply:
Example:
Note: Red LED forward voltage (V
F
) is typically
2.0V @ 2mA. Green LED forward voltage (V
F
) is
typically 3.2V @ 2mA.
The four status LED display conditions are
described in Table 3.
R
B(STAT1)
=
= 1.75k
Ω
5.5V - 2.0V
2mA
R
B(STAT1/2)
= V
ADP
- V
F(LED)
I
LED(STAT1/2)
AAT2550
Total Power Solution for Portable Applications
2550.2006.07.1.0
19
Table 3: Status LED Display Conditions.
Event Description
STAT1
STAT2
Charge Disabled or Low Supply
Charge Enabled Without Battery
Battery Charging
Charge Completed
Fault
Off
Off
Flash
1
On
Off
On
Flash
1
Off
On
On
1. Flashing rate depends on output capacitance.
相關PDF資料 |
PDF描述 |
|---|---|
| AAT2554 | Total Power Solution for Portable Applications |
| AAT2554IRN-CAP-T1 | Total Power Solution for Portable Applications |
| AAT2554IRN-CAQ-T1 | Total Power Solution for Portable Applications |
| AAT2554IRN-CAT-T1 | Total Power Solution for Portable Applications |
| AAT2554IRN-CAW-T1 | Total Power Solution for Portable Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AAT2550_08 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:Total Power Solution for Portable Applications |
| AAT2550ISK-CAA-T1 | 制造商:Skyworks Solutions Inc 功能描述:Voltage Regulators - Switching Regulators 2 step-down conv + battery charger 制造商:Skyworks Solutions Inc 功能描述:DC TO DC CONVERTER |
| AAT2552 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:Total Power Solution for Portable Applications |
| AAT2552_08 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:Total Power Solution for Portable Applications |
| AAT2552IRN-CAE-T1 | 功能描述:電荷泵 Total Pwr Solution for Portable App RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 輸出電壓:- 1.5 V to - 5.5 V, 3 V to 11 V 輸出電流:100 mA 電源電流:1 mA 最大工作溫度:+ 70 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。