- 您現在的位置：買賣IC網 > PDF目錄381232 > AAT2550 (Advanced Analog Technology,lnc.) Total Power Solution for Portable Applications PDF資料下載
參數資料
| 型號： | AAT2550 |
| 廠商： | Advanced Analog Technology,lnc. |
| 英文描述： | Total Power Solution for Portable Applications |
| 中文描述： | 總功率便攜式應用解決方案 |
| 文件頁數： | 18/35頁 |
| 文件大小： | 914K |
| 代理商： | AAT2550 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
Figure 2: I
FASTCHARGE
vs. R
SET
.
Protection Circuitry
Programmable Watchdog Timer
The AAT2550 contains a watchdog timing circuit for
the adapter input charging mode. Typically, a 0.1μF
ceramic capacitor is connected between the CT pin
and ground. When a 0.1μF ceramic capacitor is
used, the device will time a shutdown condition if
the trickle charge mode exceeds 25 minutes and a
combined trickle charge plus fast charge mode of
three hours. When the device transitions to the con-
stant voltage mode, the timing counter is reset and
will time out after three hours and shut down the
charger (see Table 2).
Table 2: Summary for a 0.1μF Used for the
Timing Capacitor.
The CT pin is driven by a constant current source
and will provide a linear response to increases in
the timing capacitor value. Thus, if the timing capac-
itor were to be doubled from the nominal 0.1μF
value, the time-out durations would be doubled.
If the programmable watchdog timer function is not
needed, it can be disabled by connecting the CT
pin to ground. The CT pin should not be left float-
ing or un-terminated, as this will cause errors in the
internal timing control circuit.
The constant current provided to charge the timing
capacitor is very small, and this pin is susceptible
to noise and changes in capacitance value.
Therefore, the timing capacitor should be physical-
ly located on the printed circuit board layout as
closely as possible to the CT pin. Since the accu-
racy of the internal timer is dominated by the
capacitance value, 10% tolerance or better ceram-
ic capacitors are recommended. Ceramic capacitor
materials, such as X7R and X5R type, are a good
choice for this application.
Over-Voltage Protection
An over-voltage event is defined as a condition
where the voltage on the BAT pin exceeds the max-
imum battery charge voltage and is set by the over-
voltage protection threshold (V
OVP
). If an over-volt-
age condition occurs, the AAT2550 charge control
will shut down the device until voltage on the BAT
pin drops below the over-voltage protection thresh-
old (V
OVP
). The AAT2550 will resume normal charg-
ing operation after the over-voltage condition is
removed. During an over-voltage event, the STAT
LEDs will report a system fault, and the actual fault
condition may be read via the DATA pin signal.
Over-Temperature Shutdown
The AAT2550 has a thermal protection control cir-
cuit which will shut down charging functions should
the internal die temperature exceed the preset
thermal limit threshold.
Battery Temperature Fault Monitoring
In the event of a battery over-temperature condi-
tion, the charge control will turn off the internal pass
device and report a battery temperature fault on the
DATApin function. The STAT LEDs will also display
a system fault. After the system recovers from a
temperature fault, the device will resume charging
operation.
The AAT2550 checks battery temperature before
starting the charge cycle, as well as during all
stages of charging. This is accomplished by moni-
toring the voltage at the TS pin. This system is
intended to use negative temperature coefficient
thermistors (NTC), which are typically integrated
into the battery package. Most of the commonly
Mode
Time
Trickle Charge (TC) Time Out
Trickle Charge (TC) +
Fast Charge (CC) Time Out
Constant Voltage (VC) Mode
Time Out
25 minutes
3 hours
3 hours
R
SET
(k
Ω
Ω
)
I
F
10
100
1000
10000
1
10
100
ADP
AAT2550
Total Power Solution for Portable Applications
18
2550.2006.07.1.0
相關PDF資料 |
PDF描述 |
|---|---|
| AAT2554 | Total Power Solution for Portable Applications |
| AAT2554IRN-CAP-T1 | Total Power Solution for Portable Applications |
| AAT2554IRN-CAQ-T1 | Total Power Solution for Portable Applications |
| AAT2554IRN-CAT-T1 | Total Power Solution for Portable Applications |
| AAT2554IRN-CAW-T1 | Total Power Solution for Portable Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AAT2550_08 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:Total Power Solution for Portable Applications |
| AAT2550ISK-CAA-T1 | 制造商:Skyworks Solutions Inc 功能描述:Voltage Regulators - Switching Regulators 2 step-down conv + battery charger 制造商:Skyworks Solutions Inc 功能描述:DC TO DC CONVERTER |
| AAT2552 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:Total Power Solution for Portable Applications |
| AAT2552_08 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:Total Power Solution for Portable Applications |
| AAT2552IRN-CAE-T1 | 功能描述:電荷泵 Total Pwr Solution for Portable App RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 輸出電壓:- 1.5 V to - 5.5 V, 3 V to 11 V 輸出電流:100 mA 電源電流:1 mA 最大工作溫度:+ 70 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。