參數資料
型號： AAT1230-1
廠商： Advanced Analog Technology,lnc.
英文描述： 18V 100mA Step-Up Converter
中文描述： 18V的100mA的升壓轉換器
文件頁數： 13/21頁
文件大?。?/td> 511K
代理商： AAT1230-1
AAT1230/1230-1
18V 100mA Step-Up Converter
1230.2006.10.1.4
13
Minimum 6.3V rated ceramic capacitors are required
at the input. Ceramic capacitors sized as small as
0603 are available which meet these requirements.
The AAT1230/1230-1 provides excellent load tran-
sient response, but large capacitance tantalum or
solid-electrolytic capacitors may be desired. These
can replace (or be used in parallel with) ceramic
capacitors. Both tantalum and OSCON-type capaci-
tors are suitable due to their low ESR and excellent
temperature stability (although they exhibit much
higher ESR than MLC capacitors). Aluminum-elec-
trolytic types are less suitable due to their high ESR
characteristics and temperature drift. Unlike MLC
capacitors, these types are polarized and proper ori-
entation on input and output pins is required. 30% to
70% voltage derating is recommended for tantalum
capacitors.
Setting the Output Voltage
The output voltage may be programmed through a
resistor divider network located from the output to
FB1 and FB2 pins to ground. Pulling the SEL pin
high activates the FB1 pin which maintains a 1.2V
reference voltage, while the FB2 reference is dis-
abled. Pulling the SEL pin low activates the FB2
pin which maintains a 0.6V reference, while the
FB1 reference is disabled.
The AAT1230/1230-1 output voltage can be pro-
grammed by one of three methods. First, the out-
put voltage can be static by pulling the SEL logic
pin either high or low. Second, the output voltage
can be dynamically adjusted between two pre-set
levels within a 2X operating range by toggling the
SEL logic pin. Third, the output can be dynamical-
ly adjusted to any of 16 preset levels within a 2X
operating range using the integrated S
2
Cwire sin-
gle wire interface via the EN/SET pin.
Option 1: Static Output Voltage
A static output voltage can be configured by pulling
the SELeither high or low. SELpin high activates the
FB1 reference pin to 1.2V (nominal). Alternatively,
the SEL pin is pulled low to activate the FB2 refer-
ence at 0.6V (nominal). Table 1 provides details of
resistor values for common output voltages from 10V
to 18V for SEL = High and SEL = Low options.
In the static configuration, the FB1 pin should be
directly connected to FB2. The resistor between
FB1 and FB2 pins is not required. See Table 1 for
static output voltages with SEL = High or SEL =
Low. SEL = High corresponds to V
OUT(1)
and SEL =
Low corresponds to V
OUT(2)
.
Option 2: Dynamic Voltage Control Using SEL Pin
The output may be dynamically adjusted between
two output voltages by toggling the SEL logic pin.
Output voltages V
OUT(1)
and V
OUT(2)
correspond to
the two output references, FB1 and FB2. Pulling
the SEL logic pin high activates V
OUT(1)
, while
pulling the SEL logic pin low activates V
OUT(2)
.
The minimum output voltage must be greater than
the specified maximum input voltage plus margin to
maintain proper operation of the AAT1230/1230-1
boost converter. In addition, the ratio of output volt-
ages V
OUT(2)
/V
OUT(1)
is always less than 2.0, corre-
sponding to a 2X (maximum) programmable range.
See Table 1 for dynamic output voltage settings
when toggling between SEL = High and SEL = Low.
SEL = High corresponds to V
OUT(1)
and SEL = Low
corresponds to V
OUT(2)
.
Table 1: SEL Pin Voltage Control Resistor
Values (1% resistor tolerance).
V
OUT(1)
(SEL = High) (SEL = Low) R1 (k
Ω
)
10.0V
12.0V
15.0V
16.0V
18.0V
–
10.0V
–
12.0V
–
15.0V
–
16.0V
–
18.0V
12.0V
10.0V
15.0V
10.0V
16.0V
10.0V
18.0V
10.0V
15.0V
12.0V
16.0V
12.0V
18.0V
12.0V
18.0V
15.0V
V
OUT(2)
R3 = 4.99k
Ω
R2 (k
Ω
)
0
0
0
0
0
0
0
0
0
0
3.32
1.65
1.24
0.562
3.01
2.49
1.65
3.32
–
–
–
–
–
36.5
44.2
57.6
61.9
69.8
78.7
95.3
121
127
143
75
76.8
76.8
78.7
90.9
93.1
93.1
115
相關PDF資料
PDF描述
AAT1230IRN-T1 18V 100mA Step-Up Converter
AAT1236 High Efficiency White LED Drivers for Backlight and Keypad
AAT1236IRN-T1 High Efficiency White LED Drivers for Backlight and Keypad
AAT1343 RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
AAT1343-T1 RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
相關代理商/技術參數
參數描述
AAT1230IRN 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:18V 100mA Step-Up Converter
AAT1230IRN-1-T1 制造商:SKYWORKS SOLUTIONS INC 功能描述:IC REG BOOST ADJ .1A 16TDFN TR 制造商:Skyworks Solutions Inc 功能描述:DC TO DC CONVERTER
AAT1230IRN-T1 制造商:Skyworks Solutions Inc 功能描述:Voltage Regulators - Switching Regulators 18V 100mA Step-Up
AAT1230ITP 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:18V 100mA Step-Up Converter
AAT1230ITP-1 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:18V 100mA Step-Up Converter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*