- 您現在的位置：買賣IC網 > PDF目錄375160 > A8431EEH-T (Allegro MicroSystems, Inc.) White LED Driver Constant Current Step-up Converter PDF資料下載
參數資料
| 型號： | A8431EEH-T |
| 廠商： | Allegro MicroSystems, Inc. |
| 元件分類： | LED驅動器 |
| 英文描述： | White LED Driver Constant Current Step-up Converter |
| 中文描述： | 白光LED驅動恒流升壓轉換器 |
| 文件頁數： | 6/10頁 |
| 文件大?。?/td> | 331K |
| 代理商： | A8431EEH-T |
6
26185.301
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
115 Northeast Cutoff, Box 15036
Allegro MicroSystems, Inc.
A8431
White LED Driver Constant Current Step-up Converter
Component Selection
The component values shown in schematic 1 are sufficient
for most applications. To reduce the output ripple, L1 may be
increased, but in most cases this results in excessive board
area and cost.
Inductor Selection
.
With an internal PWM frequency of
1.2 MHz, the optimal L1 value for most cases is 22 μH.
For worst case conditions (high output voltage and current
and low input voltage), the inductor should be rated at the
switch current limit, I
SWLIM
. If high temperature operation
is required, a derating factor will have to be considered. In
some cases, where lower inductor currents are expected,
the current rating can be decreased. Several inductor
manufacturers, including: Coilcraft, Murata, Panasonic,
Sumida, Taiyo Yuden, and TDK, have and are developing
suitable small-size inductors.
Diode Selection
.
The diode should have a low forward
voltage to reduce conduction losses. In addition, it should
have a low capacitance to reduce switching losses. Schottky
diodes can provide both these features, if carefully
selected. The forward voltage drop is a natural advantage
for Schottky diodes, and it reduces as the current rating
increases. However, as the current rating increases, the
diode capacitance also increases. As a result, the optimal
selection is usually the lowest current rating above the circuit
maximum. In this application, a current rating in the range
from 100 mA to 200 mA is usually sufficient.
Capacitor Selection
.
Because the capacitor values are low,
ceramic capacitors are the best choice for this application.
To reduce performance variation as temperature changes,
low- drift capacitor types, such as X7R and X5R, should
be used. A 1.0 μF capacitor on the VIN pin is suitable for
most applications. In cases where large inductor currents
are switched, a larger capacitor may be needed. The
output capacitor, C2, can be as small as 0.22 μF for most
applications and most input/output voltage ranges. Increasing
the capacitor value on the output aids in increasing the
efficiency of low input voltage/high output voltage
Application Information
Schematic 2. Dimming control with dc voltage
A8431
VIN
SW
EN
GND
FB
Li-ion
2.5 V to
4.2 V
C1
1.0 μF
L1
22 μH
D1
C2
0.22 μF
R1
6.3
V
C
R3
90 k
R2
5 k
Enable
1
2
3
5
6
4
OVP
conditions. Suitable capacitors are available from TDK,
Taiyo Yuden, Murata, Kemet, and AVX.
Dimming Control
LED brightness can be controlled either: (a) by modify-
ing the voltage at the top of R1 to control the LED current,
I
LOAD
, directly, or (b) by using a PWM signal on the EN pin
to chop the output.
Feedback Modulation
.
By adding a voltage drop between
the FB pin and R1, as shown in schematic 2, the LED
current, I
LOAD
, can be made to decrease. As V
C
(control
voltage) increases, the voltage drop across R2 also increases.
This causes the voltage at FB to increase, and the A8431
reduces I
LOAD
to compensate. As V
C
increases further, the
current drops to 0 A, and R2 maintains the full 95 mV on FB.
Reducing V
C
diminishes the voltage across R2 until, when
V
C
is at 95 mV there is no drop across R2 and the current
level is defined by R1. Reducing V
C
below 95 mV causes
I
LOAD
to increase further, due to the voltage drop across R2
in the reverse direction. This continues until, when V
C
is at
0 V, there is approximately 5 mV across R2. At that point,
I
LOAD
(mA), is defined as:
I
LOAD
= 100 mV
R1
where R1 is the resistance of the sense resistor (
).
Preliminary Data Sheet
Subject to Change Without Notice
December 7, 2004
相關PDF資料 |
PDF描述 |
|---|---|
| A8436 | Photoflash Capacitor Charger with IGBT Driver |
| A8436EEJTR-T | Photoflash Capacitor Charger with IGBT Driver |
| A8438 | Photoflash Capacitor Charger with IGBT Driver |
| A8438EEJTR-T | Photoflash Capacitor Charger with IGBT Driver |
| A8439 | Photoflash Capacitor Charger with IGBT Driver and Refresh |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A8431EEHTR-T | 功能描述:IC LED DRVR WHITE BCKLGHT 6-MLP RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:1 系列:- 恒定電流:- 恒定電壓:- 拓撲:PWM，切換式電容器（充電泵） 輸出數:1 內部驅動器:是 類型 - 主要:背光 類型 - 次要:白色 LED 頻率:642kHz 電源電壓:2.7 V ~ 5.5 V 輸出電壓:5V 安裝類型:表面貼裝 封裝/外殼:10-VFDFN 裸露焊盤 供應商設備封裝:10-VSON 包裝:剪切帶 (CT) 工作溫度:-30°C ~ 85°C 產品目錄頁面:1371 (CN2011-ZH PDF) 其它名稱:BD1603NUV-E2CT |
| A84334-000 | 制造商:TE Connectivity 功能描述:VARISTOR 470VDC 5MM 10% LEADED 制造商:TE Connectivity 功能描述:VARISTOR 470V 400A DISC 5MM |
| A8434 | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:6-Channel High Efficiency Charge Pump White LED Driver |
| A8434EESTR-T | 功能描述:IC LED DRVR WHITE BCKLGHT 16-MLP RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:60 系列:- 恒定電流:- 恒定電壓:- 拓撲:線性（LDO），PWM，升壓（升壓） 輸出數:8 內部驅動器:是 類型 - 主要:背光 類型 - 次要:RGB，白色 LED 頻率:500kHz ~ 1.5MHz 電源電壓:4.75 V ~ 26 V 輸出電壓:45V 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* 工作溫度:-40°C ~ 85°C |
| A8435 | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:High Efficiency Charge Pump White LED Driver |
發布緊急采購，3分鐘左右您將得到回復。