- 您現在的位置：買賣IC網 > PDF目錄375160 > A8431EEH-T (Allegro MicroSystems, Inc.) White LED Driver Constant Current Step-up Converter PDF資料下載
參數資料
| 型號： | A8431EEH-T |
| 廠商： | Allegro MicroSystems, Inc. |
| 元件分類： | LED驅動器 |
| 英文描述： | White LED Driver Constant Current Step-up Converter |
| 中文描述： | 白光LED驅動恒流升壓轉換器 |
| 文件頁數： | 5/10頁 |
| 文件大?。?/td> | 331K |
| 代理商： | A8431EEH-T |
5
26185.301
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
115 Northeast Cutoff, Box 15036
Allegro MicroSystems, Inc.
A8431
White LED Driver Constant Current Step-up Converter
Device Operation
The A8431 uses a constant-frequency, current-mode control
scheme to regulate the current through the load. The load
current produces a voltage across the external sense resistor
(R1 in schematic 1) and the input at the FB pin. This voltage
is then compared to the internal 95 mV reference to produce
an error signal. The switch current is sensed by the internal
sense resistor and compared to the load current error signal.
As the load current increases, the error signal diminishes,
reducing the maximum switch current and thus the current
delivered to the load. As
the load current
decreases, the
error signal rises, increasing the maximum switch current
and thus increasing the current delivered to the load.
To set
the load current,
ensure that the required internal
reference value of 95 mV is produced at the desired load. To
do so, select a resistance value for the sense resistor, R1 (
),
such that:
R1 = 95 mV
I
LOAD
where
I
LOAD
is the target load current (mA).
The table below shows typical values for R1. Note that the
resistance value is from the standard E96 series.
As load current is reduced, the energy required in the
dropping to 0 A for low load-current levels. This is known
as Discontinuous mode operation, and results in some low-
frequency ripple. The average load current, however, remains
regulated down to 0 A.
In Discontinuous mode, when the inductor current drops to
0 A, the voltage at the SW pin rings, due to the capacitance
in the resonant LC circuit formed by the inductor and the
capacitance of the switch and the diode. This ringing is
low-frequency and is not harmful. It can be damped with a
resistor across the inductor, but this reduces efficiency and is
not recommended.
Overvoltage Protection
An overvoltage event can occur when the LEDs become
disconnected or fail in an open state. In these cases, the
current flow through the sense resistor, R1, becomes 0 A and
thus the feedback voltage, V
FB
becomes 0 V. The A8431
compensates by increasing the on time of the switch, which
increases the output voltage.
The A8431 has built-in protection to guard against excessive
voltage on the SW pin. If the output voltage exceeds the
typical level of the Output Overvoltage Rising Limit, V
OVPR
,
then the overvoltage protection circuitry shuts off the internal
switch until the output voltage falls below the Output
Overvoltage Falling Limit, V
OVPF
. At this point, the A8431
operates normally. There is no need for an external Zener
diode for the A8431.
Target Load Current
(
I
LOAD
)
(mA)
Sense Resistor (R1)
(
)
5
19.1
10
9.53
12
7.87
15
6.34
20
4.75
0
10
20
30
40
50
60
70
80
90
100
110
120
5
10
15
20
25
I
OUT
(mA)
P
Vin = 3V, 3 LED
Vin = 5V, 3 LED
Vin = 3V, 4 LED
Vin = 5V, 4 LED
Power Dissipation versus I
OUT
Preliminary Data Sheet
Subject to Change Without Notice
December 7, 2004
相關PDF資料 |
PDF描述 |
|---|---|
| A8436 | Photoflash Capacitor Charger with IGBT Driver |
| A8436EEJTR-T | Photoflash Capacitor Charger with IGBT Driver |
| A8438 | Photoflash Capacitor Charger with IGBT Driver |
| A8438EEJTR-T | Photoflash Capacitor Charger with IGBT Driver |
| A8439 | Photoflash Capacitor Charger with IGBT Driver and Refresh |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A8431EEHTR-T | 功能描述:IC LED DRVR WHITE BCKLGHT 6-MLP RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:1 系列:- 恒定電流:- 恒定電壓:- 拓?fù)?PWM，切換式電容器（充電泵） 輸出數:1 內部驅動器:是 類型 - 主要:背光 類型 - 次要:白色 LED 頻率:642kHz 電源電壓:2.7 V ~ 5.5 V 輸出電壓:5V 安裝類型:表面貼裝 封裝/外殼:10-VFDFN 裸露焊盤 供應商設備封裝:10-VSON 包裝:剪切帶 (CT) 工作溫度:-30°C ~ 85°C 產品目錄頁面:1371 (CN2011-ZH PDF) 其它名稱:BD1603NUV-E2CT |
| A84334-000 | 制造商:TE Connectivity 功能描述:VARISTOR 470VDC 5MM 10% LEADED 制造商:TE Connectivity 功能描述:VARISTOR 470V 400A DISC 5MM |
| A8434 | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:6-Channel High Efficiency Charge Pump White LED Driver |
| A8434EESTR-T | 功能描述:IC LED DRVR WHITE BCKLGHT 16-MLP RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:60 系列:- 恒定電流:- 恒定電壓:- 拓?fù)?線性（LDO），PWM，升壓（升壓） 輸出數:8 內部驅動器:是 類型 - 主要:背光 類型 - 次要:RGB，白色 LED 頻率:500kHz ~ 1.5MHz 電源電壓:4.75 V ~ 26 V 輸出電壓:45V 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* 工作溫度:-40°C ~ 85°C |
| A8435 | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:High Efficiency Charge Pump White LED Driver |
發布緊急采購，3分鐘左右您將得到回復。