Table 1-7 A54SX16P AC Specifications for (PCI Operation) Symbol Para" />
參數資料
型號： A54SX08-TQ176I
廠商： Microsemi SoC
文件頁數： 6/64頁
文件大小： 0K
描述： IC FPGA SX 12K GATES 176-TQFP
標準包裝： 40
系列： SX
LAB/CLB數： 768
輸入/輸出數： 128
門數： 12000
電源電壓： 3 V ~ 3.6 V，4.75 V ~ 5.25 V
安裝類型： 表面貼裝
工作溫度： -40°C ~ 85°C
封裝/外殼： 176-LQFP
供應商設備封裝： 176-TQFP（24x24）
SX Family FPGAs
1- 10
v3.2
A54SX16P AC Specifications for (PCI Operation)
Table 1-7
A54SX16P AC Specifications for (PCI Operation)
Symbol
Parameter
Condition
Min.
Max.
Units
IOH(AC)
Switching Current High
0 < VOUT ≤ 1.4
1
–44
mA
1.4
≤ V
OUT < 2.4
1, 2
–44 + (VOUT – 1.4)/0.024
mA
3.1 < VOUT < VCC
1, 3
(Test Point)
VOUT = 3.1
3
–142
mA
IOL(AC)
Switching Current High
VOUT ≥ 2.2
1
95
mA
2.2 > VOUT > 0.55
1
VOUT/0.023
0.71 > VOUT > 0
1, 3
mA
(Test Point)
VOUT = 0.71
3
206
mA
ICL
Low Clamp Current
–5 < VIN ≤ –1
–25 + (VIN + 1) /0.015
mA
slewR
Output Rise Slew Rate
0.4 V to 2.4 V load4
15
V/ns
slewF
Output Fall Slew Rate
2.4 V to 0.4 V load4
15
V/ns
Notes:
1. Refer to the V/I curves in Figure 1-9 on page 1-11. Switching current characteristics for REQ# and GNT# are permitted to be one half
of that specified here; i.e., half-size output drivers may be used on these signals. This specification does not apply to CLK and RST#,
which are system outputs. “Switching Current High” specifications are not relevant to SERR#, INTA#, INTB#, INTC#, and INTD#,
which are open drain outputs.
2. Note that this segment of the minimum current curve is drawn from the AC drive point directly to the DC drive point rather than
toward the voltage rail (as is done in the pull-down curve). This difference is intended to allow for an optional N-channel pull-up.
3. Maximum current requirements must be met as drivers pull beyond the last step voltage. Equations defining these maximums (A
and B) are provided with the respective diagrams in Figure 1-9 on page 1-11. The equation defined maxima should be met by
design. In order to facilitate component testing, a maximum current test point is defined for each side of the output driver.
4. This parameter is to be interpreted as the cumulative edge rate across the specified range, rather than the instantaneous rate at any
point within the transition range. The specified load (diagram below) is optional; i.e., the designer may elect to meet this parameter
with an unloaded output per revision 2.0 of the PCI Local Bus Specification. However, adherence to both maximum and minimum
parameters is now required (the maximum is no longer simply a guideline). Since adherence to the maximum slew rate was not
required prior to revision 2.1 of the specification, there may be components in the market for some time that have faster edge rates;
therefore, motherboard designers must bear in mind that rise and fall times faster than this specification could occur, and should
ensure that signal integrity modeling accounts for this. Rise slew rate does not apply to open drain outputs.
1/2 in. max.
Pin
Output
Buffer
VCC
10 pF
1 k
Ω
1 k
Ω
相關PDF資料
PDF描述
CAT24C32WI-GT3 IC EEPROM 32KBIT 400KHZ 8SOIC
A54SX08-TQG176I IC FPGA SX 12K GATES 176-TQFP
A54SX08-1TQG176 IC FPGA SX 12K GATES 176-TQFP
AMM22DTMH CONN EDGECARD 44POS R/A .156 SLD
EP4CGX30CF23C7 IC CYCLONE IV GX FPGA 30K 484FBG
相關代理商/技術參數
參數描述
A54SX08-TQ176M 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA)
A54SX08-TQ208 制造商:未知廠家 制造商全稱:未知廠家 功能描述:54SX Family FPGAs
A54SX08-TQ208I 制造商:未知廠家 制造商全稱:未知廠家 功能描述:54SX Family FPGAs
A54SX08-TQ208M 制造商:未知廠家 制造商全稱:未知廠家 功能描述:54SX Family FPGAs
A54SX08-TQ208PP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:54SX Family FPGAs
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*