參數資料
| 型號： | A54SX08-1TQ176I |
| 廠商： | Microsemi SoC |
| 文件頁數： | 6/64頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC FPGA SX 12K GATES 176-TQFP |
| 標準包裝： | 40 |
| 系列： | SX |
| LAB/CLB數： | 768 |
| 輸入/輸出數： | 128 |
| 門數： | 12000 |
| 電源電壓： | 3 V ~ 3.6 V，4.75 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 176-LQFP |
| 供應商設備封裝： | 176-TQFP（24x24） |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
SX Family FPGAs
1- 10
v3.2
A54SX16P AC Specifications for (PCI Operation)
Table 1-7
A54SX16P AC Specifications for (PCI Operation)
Symbol
Parameter
Condition
Min.
Max.
Units
IOH(AC)
Switching Current High
0 < VOUT ≤ 1.4
1
–44
mA
1.4
≤ V
OUT < 2.4
1, 2
–44 + (VOUT – 1.4)/0.024
mA
3.1 < VOUT < VCC
1, 3
(Test Point)
VOUT = 3.1
3
–142
mA
IOL(AC)
Switching Current High
VOUT ≥ 2.2
1
95
mA
2.2 > VOUT > 0.55
1
VOUT/0.023
0.71 > VOUT > 0
1, 3
mA
(Test Point)
VOUT = 0.71
3
206
mA
ICL
Low Clamp Current
–5 < VIN ≤ –1
–25 + (VIN + 1) /0.015
mA
slewR
Output Rise Slew Rate
0.4 V to 2.4 V load4
15
V/ns
slewF
Output Fall Slew Rate
2.4 V to 0.4 V load4
15
V/ns
Notes:
1. Refer to the V/I curves in Figure 1-9 on page 1-11. Switching current characteristics for REQ# and GNT# are permitted to be one half
of that specified here; i.e., half-size output drivers may be used on these signals. This specification does not apply to CLK and RST#,
which are system outputs. “Switching Current High” specifications are not relevant to SERR#, INTA#, INTB#, INTC#, and INTD#,
which are open drain outputs.
2. Note that this segment of the minimum current curve is drawn from the AC drive point directly to the DC drive point rather than
toward the voltage rail (as is done in the pull-down curve). This difference is intended to allow for an optional N-channel pull-up.
3. Maximum current requirements must be met as drivers pull beyond the last step voltage. Equations defining these maximums (A
and B) are provided with the respective diagrams in Figure 1-9 on page 1-11. The equation defined maxima should be met by
design. In order to facilitate component testing, a maximum current test point is defined for each side of the output driver.
4. This parameter is to be interpreted as the cumulative edge rate across the specified range, rather than the instantaneous rate at any
point within the transition range. The specified load (diagram below) is optional; i.e., the designer may elect to meet this parameter
with an unloaded output per revision 2.0 of the PCI Local Bus Specification. However, adherence to both maximum and minimum
parameters is now required (the maximum is no longer simply a guideline). Since adherence to the maximum slew rate was not
required prior to revision 2.1 of the specification, there may be components in the market for some time that have faster edge rates;
therefore, motherboard designers must bear in mind that rise and fall times faster than this specification could occur, and should
ensure that signal integrity modeling accounts for this. Rise slew rate does not apply to open drain outputs.
1/2 in. max.
Pin
Output
Buffer
VCC
10 pF
1 k
Ω
1 k
Ω
相關PDF資料 |
PDF描述 |
|---|---|
| A54SX08-2TQ176 | IC FPGA SX 12K GATES 176-TQFP |
| A54SX08-1TQG176I | IC FPGA SX 12K GATES 176-TQFP |
| APA300-PQG208A | IC FPGA PROASIC+ 300K 208-PQFP |
| APA300-PQ208A | IC FPGA PROASIC+ 300K 208-PQFP |
| A54SX32A-BGG329I | IC FPGA SX 48K GATES 329-BGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A54SX08-1TQ176M | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA) |
| A54SX08-1TQ208 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:54SX Family FPGAs |
| A54SX08-1TQ208I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:54SX Family FPGAs |
| A54SX08-1TQ208M | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:54SX Family FPGAs |
| A54SX08-1TQ208PP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:54SX Family FPGAs |
發(fā)布緊急采購，3分鐘左右您將得到回復。