參數資料
型號: A1425A-2PQG100C
元件分類: FPGA
英文描述: FPGA, 310 CLBS, 2500 GATES, 200 MHz, PQFP100
封裝: PLASTIC, QFP-100
文件頁數: 8/68頁
文件大?。?/td> 489K
代理商: A1425A-2PQG100C
1-190
Package Thermal Characteristics
The device junction to case thermal characteristic is
θjc, and
the junction to ambient air characteristic is
θja. The thermal
characteristics for
θja are shown with two different air flow
rates.
Maximum junction temperature is 150
°C.
A sample calculation of the absolute maximum power
dissipation allowed for a CPGA 175-pin package at
commercial temperature and still air is as follows:
Power Dissipation
P = [ICC standby+ Iactive] * VCC + IOL * VOL * N + IOH *
(VCC – VOH) * M
(1)
Where:
ICC standby is the current flowing when no inputs or
outputs are changing.
Iactive is the current flowing due to CMOS switching.
IOL, IOH are TTL sink/source currents.
VOL, VOH are TTL level output voltages.
N equals the number of outputs driving TTL loads to
VOL.
M equals the number of outputs driving TTL loads to
VOH.
An accurate determination of N and M is problematical
because their values depend on the design and on the system
I/O. The power can be divided into two components: static
and active.
Static Power Component
Actel FPGAs have small static power components that result
in lower power dissipation than PALs or PLDs. By integrating
multiple PALs/PLDs into one FPGA, an even greater
reduction in board-level power dissipation can be achieved.
The power due to standby current is typically a small
component of the overall power. Standby power is calculated
below for commercial, worst case conditions.
The static power dissipated by TTL loads depends on the
number of outputs driving high or low and the DC load
current. Again, this value is typically small. For instance, a
32-bit bus sinking 4 mA at 0.33 V will generate 42 mW with all
outputs driving low, and 140 mW with all outputs driving high.
The actual dissipation will average somewhere between as
I/Os switch states with time.
Package Type1
Pin Count
θjc
θja
Still Air
θja
300 ft/min
Units
Ceramic Pin Grid Array
100
133
175
207
257
20
35
30
25
22
15
17
15
14
13
8
°C/W
Ceramic Quad Flatpack
132
196
256
13
55
36
30
24
18
°C/W
Plastic Quad Flatpack
100
160
208
13
10
51
33
40
26
°C/W
Very Thin Quad Flatpack
100
12
43
35
°C/W
Thin Quad Flatpack
176
11
32
25
°C/W
Power Quad Flatpack
208
0.4
17
13
°C/W
Plastic Leaded Chip Carrier
84
12
37
28
°C/W
Plastic Ball Grid Array
225
313
10
25
23
19
17
°C/W
Note:
1.
Maximum Power Dissipation in Still Air for 160-pin PQFP package is 2.4 Watts, 208-pin PQFP package is 2.4 Watts, 100-pin PQFP package
is 1.6 Watts, 100-pin VQFP package is 1.9 Watts, 176-pin TQFP package is 2.5 Watts, 84-pin PLCC package is 2.2 Watts, 208-pin RQFP
package is 4.7 Watts, 225-pin BGA package is 3.2 Watts, 313-pin BGA package is 3.5 Watts.
Absolute Maximum Power Allowed
Max. junction temp. (
°C) – Max. ambient temp. (°C)
θja (°C/W)
------------------------------------------------------------------------------------------------------------------------------
150
°C – 70°C
25
°C/W
---------------------------------
3.2 W
=
ICC
VCC
Power
2mA
5.25 V
10.5 mW
相關PDF資料
PDF描述
A1425A-2PQG100I FPGA, 310 CLBS, 2500 GATES, PQFP100
A1425A-2PQG160C FPGA, 310 CLBS, 2500 GATES, 200 MHz, PQFP160
A1425A-2PQG160I FPGA, 310 CLBS, 2500 GATES, PQFP160
A1425A-2VQG100C FPGA, 310 CLBS, 2500 GATES, 200 MHz, PQFP100
A1425A-2VQG100I FPGA, 310 CLBS, 2500 GATES, PQFP100
相關代理商/技術參數
參數描述
A1425A-2PQG100I 制造商:Microsemi Corporation 功能描述:FPGA ACT 3 2.5K GATES 310 CELLS 200MHZ 0.8UM 5V 100PQFP - Trays
A1425A-2PQG160C 制造商:Microsemi Corporation 功能描述:FPGA ACT 3 2.5K GATES 310 CELLS 200MHZ 0.8UM 5V 160PQFP - Trays
A1425A-2PQG160I 制造商:Microsemi Corporation 功能描述:FPGA ACT 3 2.5K GATES 310 CELLS 200MHZ 0.8UM 5V 160PQFP - Trays
A1425A-2VQ100C 制造商:Microsemi SOC Products Group 功能描述:FPGA ACT 3 2.5K GATES 310 CELLS 200MHZ 0.8UM 5V 100VQFP - Trays
A1425A-2VQ100I 制造商:Microsemi Corporation 功能描述:FPGA ACT 3 2.5K GATES 310 CELLS 200MHZ 0.8UM 5V 100VQFP - Trays