- 您現在的位置：買賣IC網 > PDF目錄25514 > 951402AGLF (INTEGRATED DEVICE TECHNOLOGY INC) 210 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 PDF資料下載
參數資料
| 型號： | 951402AGLF |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 時鐘產生/分配 |
| 英文描述： | 210 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| 封裝： | 6.10 MM, 0.50 MM PITCH, GREEN, MO-153, TSSOP-48 |
| 文件頁數： | 13/25頁 |
| 文件大?。?/td> | 320K |
| 代理商： | 951402AGLF |
20
Integrated
Circuit
Systems, Inc.
ICS951402
Advance Information
0660—05/05/05
Fig. 1
Shared Pin Operation -
Input/Output Pins
The I/O pins designated by (input/output) serve as dual
signal functions to the device. During initial power-up, they
act as input pins. The logic level (voltage) that is present on
these pins at this time is read and stored into a 5-bit internal
data latch. At the end of Power-On reset, (see AC
characteristics for timing values), the device changes the
mode of operations for these pins to an output function. In
this mode the pins produce the specified buffered clocks to
external loads.
To program (load) the internal configuration register for
these pins, a resistor is connected to either the VDD (logic 1)
power supply or the GND (logic 0) voltage potential. A 10
Kilohm (10K) resistor is used to provide both the solid CMOS
programming voltage needed during the power-up
programming period and to provide an insignificant load on
the output clock during the subsequent operating period.
Via to
VDD
Clock trace to load
Series Term. Res.
Programming
Header
Via to Gnd
Device
Pad
2K
W
8.2K
W
Figure 1 shows a means of implementing this function
when a switch or 2 pin header is used. With no jumper is
installed the pin will be pulled high. With the jumper in
place the pin will be pulled low. If programmability is not
necessary, than only a single resistor is necessary. The
programming resistors should be located close to the series
termination resistor to minimize the current loop area. It is
more important to locate the series termination resistor
close to the driver than the programming resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| 951402AFLF | 210 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| 951402AFLFT | 210 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| 951411BGLF | 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| 951412AFLFT | 220 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| 951412AGLFT | 220 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 951402AGLFT | 制造商:Integrated Device Technology Inc 功能描述:Programmable PLL Dual 48-Pin TSSOP T/R |
| 951403-9010806-AR | 功能描述:集管和線殼 3P BD STCK HDR 1R THRU-HOLE 10U AU RoHS:否 產品種類:1.0MM Rectangular Connectors 產品類型:Headers - Pin Strip 系列:DF50 觸點類型:Pin (Male) 節距:1 mm 位置/觸點數量:16 排數:1 安裝風格:SMD/SMT 安裝角:Right 端接類型:Solder 外殼材料:Liquid Crystal Polymer (LCP) 觸點材料:Brass 觸點電鍍:Gold 制造商:Hirose Connector |
| 951403-9011106-AR | 功能描述:集管和線殼 3P BD STCK HDR 1R THRU-HOLE 10U AU RoHS:否 產品種類:1.0MM Rectangular Connectors 產品類型:Headers - Pin Strip 系列:DF50 觸點類型:Pin (Male) 節距:1 mm 位置/觸點數量:16 排數:1 安裝風格:SMD/SMT 安裝角:Right 端接類型:Solder 外殼材料:Liquid Crystal Polymer (LCP) 觸點材料:Brass 觸點電鍍:Gold 制造商:Hirose Connector |
| 951403-9011506-AR | 功能描述:集管和線殼 3P BD STCK HDR 1R THRU-HOLE 10U AU RoHS:否 產品種類:1.0MM Rectangular Connectors 產品類型:Headers - Pin Strip 系列:DF50 觸點類型:Pin (Male) 節距:1 mm 位置/觸點數量:16 排數:1 安裝風格:SMD/SMT 安裝角:Right 端接類型:Solder 外殼材料:Liquid Crystal Polymer (LCP) 觸點材料:Brass 觸點電鍍:Gold 制造商:Hirose Connector |
| 951403-9011906-AR | 功能描述:集管和線殼 3P BD STCK HDR 1R THRU-HOLE 10U AU RoHS:否 產品種類:1.0MM Rectangular Connectors 產品類型:Headers - Pin Strip 系列:DF50 觸點類型:Pin (Male) 節距:1 mm 位置/觸點數量:16 排數:1 安裝風格:SMD/SMT 安裝角:Right 端接類型:Solder 外殼材料:Liquid Crystal Polymer (LCP) 觸點材料:Brass 觸點電鍍:Gold 制造商:Hirose Connector |
發布緊急采購，3分鐘左右您將得到回復。