- 您現在的位置：買賣IC網 > PDF目錄24788 > 935208600026 (NXP SEMICONDUCTORS) LIQUID CRYSTAL DISPLAY DRIVER, UUC56 PDF資料下載
參數資料
| 型號： | 935208600026 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 顯示驅動器 |
| 英文描述： | LIQUID CRYSTAL DISPLAY DRIVER, UUC56 |
| 封裝： | DIE-56 |
| 文件頁數： | 33/46頁 |
| 文件大小： | 246K |
| 代理商： | 935208600026 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
1998 Jul 30
39
Philips Semiconductors
Product specication
Universal LCD driver for low multiplex
rates
PCF8576C
15 SOLDERING
15.1
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our
“Data Handbook IC26; Integrated Circuit Packages”
(order code 9398 652 90011).
15.2
Reow soldering
Reflow soldering techniques are suitable for all LQFP and
VSO packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
infrared/convection heating in a conveyor type oven.
Throughput times (preheating, soldering and cooling) vary
between 50 and 300 seconds depending on heating
method. Typical reflow peak temperatures range from
215 to 250
°C.
15.3
Wave soldering
15.3.1
LQFP
Wave soldering is not recommended for LQFP packages.
This is because of the likelihood of solder bridging due to
closely-spaced leads and the possibility of incomplete
solder penetration in multi-lead devices.
CAUTION
Wave soldering is NOT applicable for all LQFP
packages with a pitch (e) equal or less than 0.5 mm.
If wave soldering cannot be avoided, for LQFP
packages with a pitch (e) larger than 0.5 mm, the
following conditions must be observed:
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave)
soldering technique should be used.
The footprint must be at an angle of 45° to the board
direction and must incorporate solder thieves
downstream and at the side corners.
15.3.2
VSO
Wave soldering techniques can be used for all VSO
packages if the following conditions are observed:
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.
The longitudinal axis of the package footprint must be
parallel to the solder flow.
The package footprint must incorporate solder thieves at
the downstream end.
15.3.3
METHOD (LQFP AND VSO)
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260
°C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150
°C within
6 seconds. Typical dwell time is 4 seconds at 250
°C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
15.4
Repairing soldered joints
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300
°C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320
°C.
相關PDF資料 |
PDF描述 |
|---|---|
| 935208610005 | LIQUID CRYSTAL DISPLAY DRIVER, UUC56 |
| 935261851026 | LIQUID CRYSTAL DISPLAY DRIVER, UUC56 |
| 935263925005 | LIQUID CRYSTAL DISPLAY DRIVER, UUC56 |
| 935264071026 | LIQUID CRYSTAL DISPLAY DRIVER, UUC56 |
| 06771.25 | Axial Lead and Cartridge Fuses - Ceramic Body |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 9-352112-9 | 制造商:TE Connectivity 功能描述:Z-PACK SHLD.LOWER C - Bulk |
| 9-352151-3 | 制造商:TE Connectivity 功能描述:ZP,22C.F.U.SH.44MMW/O LUBE - Tape and Reel 制造商:TE CONNECTIVITY 功能描述:ZP,22C.F.U.SH.44MMW/O LUBE |
| 9-352151-9 | 制造商:TE Connectivity 功能描述:ZP,22C.F.U.SH.44MM - Bulk |
| 935218-17 | 制造商:JANCO 功能描述:935218-17 |
| 9352370001 | 功能描述:HEAT SHRINK SLEEVE RoHS:是 類別:線纜，導線 - 管理 >> 標簽，標記 系列:HT-SCE 標準包裝:250 系列:CM-SCE 標簽類型:標準 標簽尺寸:2.00" x 0.25"（50.8mm x 6.4mm） 顏色:白 材質:聚烯烴 適用于相關產品:點陣打印機 包裝:* 工作溫度:-55°C ~ 135°C 其它名稱:A105291CM-SCE-TP-1/4-4H-9 |
發布緊急采購，3分鐘左右您將得到回復。