- 您現在的位置：買賣IC網 > PDF目錄364542 > 87LPC767 (NXP Semiconductors N.V.) Low power, low price, low pin count(20 pin) microcontroller with 4 kB OTP and 8-bit A/D(帶4 kB OTP和8位A/D的低功耗，低價格，少引腳（20引腳）的微控制器) PDF資料下載
參數資料
| 型號： | 87LPC767 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Low power, low price, low pin count(20 pin) microcontroller with 4 kB OTP and 8-bit A/D(帶4 kB OTP和8位A/D的低功耗，低價格，少引腳（20引腳）的微控制器) |
| 中文描述： | 低功耗，低價格，低引腳數（20針）與4 KB的檢察官辦公室和8位A / D（帶4 KB的檢察官和8位A / D轉換的低功耗，低價格，少引腳（20引微控制器腳）的微控制器） |
| 文件頁數： | 12/61頁 |
| 文件大?。?/td> | 296K |
| 代理商： | 87LPC767 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
Philips Semiconductors
Preliminary specification
87LPC767
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP and 8-bit A/D converter
2000 Feb 02
9
ADCON
Address: C0h
Bit addressable
Reset Value: 00h
BIT
SYMBOL
FUNCTION
ADCON.7
ENADC
When ENADC = 1, the A/D is enabled and conversions may take place. Must be set 10
microseconds before a conversion is started. ENADC cannot be cleared while ADCS or ADCI
are 1.
ADCON.6
-
Reserved for future use. Should not be set to 1 by user programs.
ADCON.5
-
Reserved for future use. Should not be set to 1 by user programs.
ADCON.4
ADCI
A/D conversion complete/interrupt flag. This flag is set when an A/D conversion is completed.
This bit will cause a hardware interrupt if enabled and of sufficient priority. Must be cleared by
software.
ADCON.3
ADCS
A/D start. Setting this bit by software starts the conversion of the selected A/D input. ADCS
remains set while the A/D conversion is in progress and is cleared automatically upon
completion. While ADCS or ADCI are one, new start commands are ignored.
ADCI, ADCS
A/D Status
0 0
A/D not busy, a conversion can be started.
0 1
A/D busy, the start of a new conversion is blocked.
1 0
An A/D conversion is complete. ADCI must be cleared prior to starting a new conversion.
1 1
An A/D conversion is complete. ADCI must be cleared prior to starting a new conversion. This
state exists for one machine cycle as an A/D conversion is completed.
ADCON.2
RCCLK
When RCCLK = 0, the CPU clock is used as the A/D clock. When RCCLK = 1, the internal RC
oscillator is used as the A/D clock. This bit is writable while ADCS and ADCI are 0.
ADCON.1, 0
AADR1,0
Along with AADR0, selects the A/D channel to be converted. These bits can only be written
while ADCS and ADCI are 0.
AADR1, AADR0
A/D Input Selected
0 0
AD0 (P0.3).
0 1
AD1 (P0.4).
1 0
AD2 (P0.5).
1 1
AD3 (P0.6).
7
6
5
4
3
2
1
0
ENADC
-
-
ADCI
ADCS
RCCLK
AADR1
AADR0
SU01354
Figure 2. A/D Control Register (ADCON)
A/D Timing
The A/D may be clocked in one of two ways. The default is to use
the CPU clock as the A/D clock source. When used in this manner,
the A/D completes a conversion in 31 machine cycles. The A/D may
be operated up to the maximum CPU clock rate of 20 MHz, giving a
conversion time of 9.3
μ
s. The formula for calculating A/D
conversion time when the CPU clock runs the A/D is: 186
μ
s / CPU
clock rate (in MHZ). To obtain accurate A/D conversion results, the
CPU clock must be at least 1 MHz.
The A/D may also be clocked by the on-chip RC oscillator, even if
the RC oscillator is not used as the CPU clock. This is accomplished
by setting the RCCLK bit in ADCON. This arrangement has several
advantages. First, the A/D conversion time is faster at lower CPU
clock rates. Also, the CPU may be run at speeds below 1 MHz
without affecting A/D accuracy. Finally, the Power Down mode may
be used to completely shut down the CPU and its oscillator, along
with other peripheral functions, in order to obtain the best possible
A/D accuracy. This should not be used if the MCU uses an external
clock source greater than 4 MHz.
When the A/D is operated from the RCCLK while the CPU is running
from another clock source, 3 or 4 machine cycles are used to
synchronize A/D operation. The time can range from a minimum of 3
machine cycles (at the CPU clock rate) + 108 RC clocks to a
maximum of 4 machine cycles (at the CPU clock rate) + 112 RC
clocks.
Example A/D conversion times at various CPU clock rates are
shown in Table 1. In Table 1, maximum times for RCCLK = 1 use an
RC clock frequency of 4.5 MHz (6 MHz - 25%). Minimum times for
RCCLK = 1 use an RC clock frequency of 7.5 MHz (6 MHz + 25%).
Nominal time assume an ideal RC clock frequency of 6 MHz and an
average of 3.5 machine cycles at the CPU clock rate.
相關PDF資料 |
PDF描述 |
|---|---|
| 87LPC768 | Low power, low price, low pin count(20 pin) microcontroller with 4 kB OTP and 8-bit A/D,and Pulse Width Modulator(帶4 kB OTP、8位A/D和脈寬調節的低功耗，低價格，少引腳（20引腳）的微控制器) |
| 87LPC769 | Low power, low price, low pin count(20 pin) microcontroller with 4 kB OTP and 8-bit A/D,and DAC(帶4 kB OTP、8位A/D和D/A轉換的低功耗，低價格，少引腳（20引腳）的微控制器) |
| 87N-1000A-0C | Signal Conditioner |
| 87N-1000A-0L | Signal Conditioner |
| 87N-1000A-0P | Signal Conditioner |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 87LPC768 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low power, low price, low pin count 20 pin microcontroller with 4 kB OTP 8-bit A/D,and Pulse Width Modulator |
| 87LPC768FN | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 87LPC769 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low power, low price, low pin count 20 pin microcontroller with 4 kB OTP 8-bit A/D, and DAC |
| 87MCW4MD | 制造商:Siemens 功能描述: |
| 87MCW4MF | 制造商:Siemens 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。