- 您現在的位置：買賣IC網 > PDF目錄364542 > 87C751 (NXP Semiconductors N.V.) 80C51 8-Bit Microcontroller Family2K/64 OTP/ROM, I 2 C, low pin count(80C51 8位微控制器系列（2K/64 OTP/ROM，IIC，低引腳數）) PDF資料下載
參數資料
| 型號： | 87C751 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 80C51 8-Bit Microcontroller Family2K/64 OTP/ROM, I 2 C, low pin count(80C51 8位微控制器系列（2K/64 OTP/ROM，IIC，低引腳數）) |
| 中文描述： | 80C51的8位微控制器Family2K/64檢察官辦公室/光盤，的I 2 C，低引腳數（80C51的8位微控制器系列（2K/64檢察官辦公室/光盤，進口證，低引腳數）） |
| 文件頁數： | 16/24頁 |
| 文件大?。?/td> | 211K |
| 代理商： | 87C751 |
Philips Semiconductors
Product specification
83C751/87C751
80C51 8-bit microcontroller family
2K/64 OTP/ROM, I
2
C, low pin count
1998 May 01
16
Table 4.
Interaction of TIRUN with SLAVEN, MASTRQ, and MASTER
SLAVEN,
MASTRQ,
MASTER
TIRUN
OPERATING MODE
All 0
0
The I
2
C interface is disabled. Timer I is cleared and does not run. This is the state assumed after a reset. If an I
2
C
application wants to ignore the I
2
C at certain times, it should write SLAVEN, MASTRQ, and TIRUN all to zero.
The I
2
C interface is disabled. Timer I operates as a free-running time base. Use this mode only in non-I
2
C
applications.
The I
2
C interface is enabled. The 3 low-order bits of Timer I run for min-time generation, but the hi-order bits do
not, so that there is no checking for I
2
C being “hung.” This configuration can be used for very slow I
2
C operation.
The I
2
C interface is enabled. Timer I runs during frames on the I
2
C, and is cleared by transitions on SCL, and by
Start and Stop conditions. This is the normal state for I
2
C operation.
All 0
1
Any or all 1
0
Any or all 1
1
Table 5.
CT1, CT0 Values
CT1, CT0
OSC/12 COUNT
f
OSC
MAX
16.8MHz
TIMEOUT PERIOD
10
7
1023 cycles
01
6
14.4MHz
1022 cycles
00
5
12.0MHz
1021 cycles
11
4
9.6MHz
1020 cycles
I
2
C Register I2STA
READ ONLY
7
6
5
4
3
2
1
0
–
IDLE
XDATA
XACTV
MAKSTR
MAKSTP
XSTR
XSTP
MSB
LSB
This register is read only and reflects the internal status of the I
2
C
hardware. IDLE, XSTR, and XSTP reflect the status of the like
named bits in the I2CON register.
XDATA
XACTV
MAKSTR This bit is high while the hardware is effecting a start
condition.
MAKSTP This bit is high while the hardware is effecting a stop
condition.
XSTR
This bit is active while the hardware is effecting a
repeated start condition.
XSTP
This bit is active while the hardware is effecting a
repeated stop condition.
The content of the transmitter buffer.
Transmitter active.
Interrupts
The interrupt structure is a five-source, one-level interrupt system.
Interrupt sources common to the 80C51 are the external interrupts
(INT0, INT1) and the timer/counter interrupt (ET0). The I
2
C interrupt
(EI2) and Timer I interrupt (ETI) are the other two interrupt sources.
The interrupt sources are listed below in their order of polling
sequence priority.
Upon interrupt or reset the program counter is loaded with specific
values for the appropriate interrupt service routine in program
memory. These values are:
Program Memory
Address
000
003
00B
013
01B
023
Event
Reset
INT0
Counter/Timer 0
INT1
Timer I
I
2
C
Priority
Highest
Lowest
The interrupt enable register (IE) is used to individually enable or
disable the five sources. Bit EA in the interrupt enable register can
be used to globally enable or disable all interrupt sources. The
interrupt enable register is described below. All other interrupt details
are based on the 80C51 interrupt architecture.
Interrupt Enable Register
7
6
5
4
3
2
1
0
EA
X
X
EI2
ETI
EX1
ET0
EX0
Symbol Position
Function
EA
IE.7
Disables all interrupts. If EA = 0, no interrupt
will be acknowledged. If EA = 1, each interrupt
source is individually enabled or disabled by
setting or clearing its enable bit
–
IE.6
Reserved
–
IE.5
Reserved
EI2
IE.4
Enables or disables the I
2
C interrupt.
If EI2 = 0, the I
2
C interrupt is disabled
ETI
IE.3
Enables or disables the Timer I overflow
interrupt. If ETI = 0, the Timer I interrupt is
disabled.
EX1
IE.2
Enables or disables external interrupt 1.
If EX1 = 0, external interrupt 1 is disabled.
ET0
IE.1
Enables or disables the Timer 0 overflow
interrupt. If ET0 = 0, theTimer 0 interrupt is
disabled.
EX0
IE.0
Enables or disables external interrupt 0.
If EX0 = 0, external interrupt 0 is disabled.
相關PDF資料 |
PDF描述 |
|---|---|
| 87C752 | 80C51 8-bit microcontroller family 2K/64 OTP/ROM, 5 channel 8 bit A/D, I2C, PWM, low pin count |
| 87C754 | 80C51 8-bit microcontroller family 4K/256 OTP/ROM, DAC, comparator, UART, reference |
| 87FC3-201 | LEITERPLATTENTASTER SYSTEM 87 PK4 |
| 87CC3-201 | LEITERPLATTENTASTER SYSTEM 87 1ST |
| 87DC3-201 | LEITERPLATTENTASTER SYSTEM 87 PK2 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 87C751/BLA | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| 87C751/BLA/OT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| 87C751-16/BLA | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| 87C751-16/BLA/OT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| 87C752 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80C51 8-bit microcontroller family 2K/64 OTP/ROM, 5 channel 8 bit A/D, I2C, PWM, low pin count |
發布緊急采購，3分鐘左右您將得到回復。