- 您現在的位置：買賣IC網 > PDF目錄294482 > 85304AG-01 (INTEGRATED DEVICE TECHNOLOGY INC) 85304 SERIES, LOW SKEW CLOCK DRIVER, 5 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO20 PDF資料下載
參數資料
| 型號： | 85304AG-01 |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 時鐘及定時 |
| 英文描述： | 85304 SERIES, LOW SKEW CLOCK DRIVER, 5 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO20 |
| 封裝： | 6.50 X 4.40 MM, 0.92 MM PITCH, MO-153, TSSOP-20 |
| 文件頁數： | 15/15頁 |
| 文件大?。?/td> | 760K |
| 代理商： | 85304AG-01 |
ICS85304-01
LOW SKEW, 1-TO-5 DIFFERENTIAL-TO- 3.3V LVPECL FANOUT BUFFER
IDT / ICS 3.3V LVPECL FANOUT BUFFER
9
ICS85304AG-01 REV. E JULY 8, 2008
Recommendations for Unused Input and Output Pins
Inputs:
LVCMOS Control Pins
All control pins have internal pull-ups or pull-downs; additional
resistance is not required but can be added for additional
protection. A 1k
resistor can be used.
CLK/nCLK Inputs
For applications not requiring the use of the differential input, both
CLK and nCLK can be left floating. Though not required, but for
additional protection, a 1k
resistor can be tied from CLK to
ground.
Outputs:
LVPECL Outputs
All unused LVPECL outputs can be left floating. We recommend
that there is no trace attached. Both sides of the differential output
pair should either be left floating or terminated.
Termination for 3.3V LVPECL Outputs
The clock layout topology shown below is a typical termination for
LVPECL outputs. The two different layouts mentioned are
recommended only as guidelines.
FOUT and nFOUT are low impedance follower outputs that
generate ECL/LVPECL compatible outputs. Therefore, terminating
resistors (DC current path to ground) or current sources must be
used for functionality. These outputs are designed to drive 50
transmission lines. Matched impedance techniques should be
used to maximize operating frequency and minimize signal
distortion. Figures 3A and 3B show two different layouts which are
recommended only as guidelines. Other suitable clock layouts may
exist and it would be recommended that the board designers
simulate to guarantee compatibility across all printed circuit and
clock component process variations.
Figure 3A. 3.3V LVPECL Output Termination
Figure 3B. 3.3V LVPECL Output Termination
V
CC - 2V
50
50
RTT
Z
o = 50
Z
o = 50
FOUT
FIN
RTT =
Z
o
1
((V
OH + VOL) / (VCC – 2)) – 2
3.3V
125
125
84
84
Z
o = 50
Z
o = 50
FOUT
FIN
相關PDF資料 |
PDF描述 |
|---|---|
| 85304AG-01T | 85304 SERIES, LOW SKEW CLOCK DRIVER, 5 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO20 |
| 853134 | 147 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, PRESS FIT |
| 8532AY-01LFT | 8532 SERIES, LOW SKEW CLOCK DRIVER, 17 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PQFP52 |
| 8535AG-21 | 8535 SERIES, LOW SKEW CLOCK DRIVER, 2 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO14 |
| 8535AG-21LF | 8535 SERIES, LOW SKEW CLOCK DRIVER, 2 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO14 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 85304AG-01LF | 功能描述:時鐘緩沖器 1:5 LVPECL Fanout Buffer RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
| 85304AG-01LFT | 功能描述:時鐘驅動器及分配 1:5 LVPECL Fanout Buffer RoHS:否 制造商:Micrel 乘法/除法因子:1:4 輸出類型:Differential 最大輸出頻率:4.2 GHz 電源電壓-最大: 電源電壓-最小:5 V 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-8 封裝:Reel |
| 85304AG-01T | 制造商:Integrated Device Technology Inc 功能描述:CLOCK DRVR 2-IN LVPECL 20TSSOP - Tape and Reel |
| 85304AGI-01LF | 功能描述:時鐘驅動器及分配 RoHS:否 制造商:Micrel 乘法/除法因子:1:4 輸出類型:Differential 最大輸出頻率:4.2 GHz 電源電壓-最大: 電源電壓-最小:5 V 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-8 封裝:Reel |
| 85304AGI-01LFT | 制造商:Integrated Device Technology Inc 功能描述:NETCOM - Bulk |
發布緊急采購，3分鐘左右您將得到回復。