- 您現在的位置：買賣IC網 > PDF目錄7077 > 8343 (3M)WORKSURFACE RIGID ESD DISSP BGE PDF資料下載
參數資料
| 型號： | 8343 |
| 廠商： | 3M |
| 文件頁數： | 13/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | WORKSURFACE RIGID ESD DISSP BGE |
| 標準包裝： | 1 |
| 系列： | 8300 |
| 墊子類型： | 桌子，工作臺 |
| 形狀： | 矩形 |
| 長度： | 3'（0.91m） |
| 寬： | 2'（0.61m） |
| 厚度： | 0.13"（3.30mm） |
| 顏色： | 淺褐 |
| 材質： | Laminate |
| 特點： | 耗散 |
| 包括： | 接地軟線，接地卡扣 |
| 其它名稱： | 05400718618 98079815845 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁
6
78-8136-3801-8
D.
The laminate should be stored at room temperature [70°F (21°C)] and 50% R.H. or greater for at least
48 hours before forming. If it is not possible to expose the laminate sheets to this high humidity for
48 hours before forming then proceed with the following. Put a layer of wet paper towels or cloths
on the top and bottom of each piece of laminate in the area to be formed. Keep it in this condition for
approximately 24 hours. Remove the wet cloths and dry the surface moisture from the back side of the
laminate with a dry cloth. This will allow the adhesive to stick to the laminate.
E.
Apply the adhesive according to the manufacturers’ recommendations.
F.
Heat to 325°F on backside, 350° 375°F on front. The laminate must reach optimum bending
temperature within 3060 seconds. Ensure that proper temperature has been reached prior to bending
and do not force bending. When laminate is at the proper temperature to be formed, it should be fairly
soft and pliable; it need not be forced into shape. Upon reaching temperature, it should be formed
immediately. Once formed, the laminate should be held under pressure until cooled.
G.
This optimum bending temperature should be measured; the easiest method of measurement is the
Tempilaq/Tempilstik. The Tempilaq/Tempilstik mark should be made on the back of the sheet. The
temperature should be uniform over the entire laminate surface in the area to be bent; a difference as
small as 5°F could result in cracking.
H.
Laminate is more easily formed when the bend is made in the machine direction; that is, parallel to the
sanding marks on the back (e.g., along the 8 ft. dimension of a 4 ft. x 8 ft. sheet). This is the orientation
of the fibers in the papers; it is easier to bend the material between the fibers than to bend the fibers.
I.
Increasing the ambient humidity by 5% will improve formability, but will also increase the probability
of excessive shrinkage.
9.0
Substrates
A.
The standard particle board used for most bench tops is 45 lb. (21 kg) density industrial grade. Although
the thickness can vary, 1.125 in. is commonly used. When the top is completed (including the backer),
the nominal thickness is 1.25 in. Particle board in 60 lb. density is also available, but is more expensive
and the improvement over the more common 45 lb. material is not significant. Unmounted laminate
sheets have low impact strength and the type of substrate covered will play a major role in determining
the impact strength of the finished product.
B.
Plywood may be used as a substrate, but it must be very smooth or the grain of the wood will
“telegraph” through the laminate.
Caution: Voids (knot holes) in the veneers below the top veneer could cause impact failure.
C.
MasoniterM is also a suitable substrate. The untempered type (no oils) is preferred.
D.
Metal is a suitable substrate. However, if contact adhesive is used, the adhesive on the metal must be
dried for a longer time to ensure that solvents have evaporated. If this is not done, a poor bond may
result.
E.
Several materials are not recommended for use as a substrate:
Underlayment particle board
Wafer board
Plaster board
Gypsum board
10.0 Backer
A backing sheet (“backer”) may be required on the bottom/back of the substrate if (a) the surface area to be
covered is large and needs support, or (b) if warping due to moisture variation is a problem. The use of a backer
is recommended as good general practice. The three common types of backer used are:
A.
Standard phenolic sheet: most commonly used and dark brown in color.
B.
Balancer sheet: standard laminate material with the decorative/top surface sanded. Material rejected for
cosmetic reasons is frequently used.
相關PDF資料 |
PDF描述 |
|---|---|
| 2-1419104-2 | RELAY GEN PURPOSE SPST 30A 48V |
| 431301-23-0 | TERM BARRIER 23CIRC 1 ROW .4375 |
| V23061B1005A301 | RELAY GEN PURPOSE SPDT 8A 12V |
| GP1500R-0.010-02-0816 | THERMAL PAD .010" 8"X16" GP1500R |
| 431201-23-0 | TERM BARRIER 23CIRC 1 ROW .4375 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 8-34304-1 | 功能描述:端子 SPLICE CE 22-14 RoHS:否 制造商:AVX 產品:Junction Box - Wire to Wire 系列:9826 線規:26-18 接線柱/接頭大小: 絕緣: 顏色:Red 型式:Female 觸點電鍍:Tin over Nickel 觸點材料:Beryllium Copper, Phosphor Bronze 端接類型:Crimp |
| 8-34306-1 | 制造商:TE Connectivity 功能描述:SPLICES TERM 16-22AWG 19.05MM TIN - Bulk |
| 8-34308-2 | 制造商:TE Connectivity 功能描述:SPLICES TERM 10-22AWG 24.77MM TIN - Bulk |
| 83431032A35 | 制造商:n/a 功能描述:Ships in 2 days |
| 8-34313-1 | 功能描述:端子 PIDG HK 22-16 COM 22-18 MIL 6 RoHS:否 制造商:AVX 產品:Junction Box - Wire to Wire 系列:9826 線規:26-18 接線柱/接頭大小: 絕緣: 顏色:Red 型式:Female 觸點電鍍:Tin over Nickel 觸點材料:Beryllium Copper, Phosphor Bronze 端接類型:Crimp |
發布緊急采購，3分鐘左右您將得到回復。