- 您現在的位置：買賣IC網 > PDF目錄376465 > 80-0206-R (Electronic Theatre Controls, Inc.) Speech Recognition Processor PDF資料下載
參數資料
| 型號： | 80-0206-R |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Speech Recognition Processor |
| 中文描述： | 語音識別處理器 |
| 文件頁數： | 29/49頁 |
| 文件大?。?/td> | 527K |
| 代理商： | 80-0206-R |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
Data Sheet
RSC-4128
Because it is intended to “l(fā)isten” continuously at very low power levels, the Audio Wakeup unit must detect each of
these events without any processor interaction. The processor configures and enables the unit under program
control before going into Idle mode. Audio Wakeup is not available in Sleep mode because the unit requires the
CLK2 signal. The detection signal from the Audio Wakeup unit can trigger a wakeup event, which starts the
processor and allows further audio processing. The processor inputs to the Audio Wakeup are an enable signal and
control signals to select for which sound to listen. See schematic 1-3 for details on this implementation.
Schematic 1-3
29
P/N 80-0206-R
2006 Sensory Inc.
V
D2
1N4148
C9
.01
A
R2
1.8K
C5
220uF
NOTE 7
C2
2.2uF
C8
3300pF
NOTE 2
R1
270
A
A
(Px.n is any available port
I/O pin)
D3
1N4148
C10
.01
Px.n
Vdd
270
NOTE 3
AVdd
C6
.047
Example using one
microphone for normal
operation only
C4
.1
D2
1N4148
NOTE 4
RSC-4x
V
G
C1
M
C5
NOTE 7
C11
D4
1N4148
Px.n
NOTE 6
R2
G
AVdd
M
A
NOTE 7
NOTE 6
MK1
MICROPHONE
1
2
V
RNOTE 5
RSC-4x
Vdd
V
C7
.1
R3
510
NOTE 2
C6
.1
C2
2.2uF
C3
C1
.1
NOTE 3
BT1
3V
1
2
NOTES:
1. Optional. This capacitor MAY reduce noise coupled into the
mic input on a noisy PCB.
2. If used, this capacitor MUST be placed close to the
RSC-4128 AGND and MIC1IN pads.
3. Place close to MICIN1.
4. These capacitors may be used to reduce high frequency
response. The tradeoff is reduced amplitude.
5. For reducing system ESD susceptibility.
6. Typical value. Refer to Sensory Design Note 80-0259
"Selecting a Microphone" to determine proper value for your
application
7. SETTING RESISTOR AND CAPACITOR VALUES IN THE MICROPHONE
POWER LINE FILTER CIRCUIT:
The capacitor value should be between 220 and 30 ufd.
The resistor value should be between 300 and 2000 ohms.
Within these ranges;
Select the largest capacitor consistent with other
constraints (cost, size,etc.)
For this capacitor, select a resistor such that the RC
time constant is ~60msec.
* Refer to Sensory Design Note 80-0073 "Speech Recognition
Hardware Design" for information on proper microphone
selection and housing design, PCB layout, as well as test and
evaluation procedures to verify proper design and operation.
* Sensory offers a FREE Design Review Service. Detatils of
this service are also included in 80-0073.
C8
.1
C7
.1
V
R3
510
D1
1N4148
A
NOTE 5
Recommended
AVdd
1.8K
Vdd
G
V
M
D1
1N4148
NOTE 7
Example using one microphone for
both Audio Wakeup and normal
operation
C9
3300pF
NOTE 1
MK1
MICROPHONE
1
2
C4
.1
A
R4
510
NOTE 1
C3
1uF
A
M
(Px.n is any available port
I/O pin)
The RSC-4128 FluentChip library contains routines for detecting each of the four audio events listed above.
These routines also manage powerdown appropriately. See the “FluentChip Technology Library Manual” for
reference code to invoke these routines.
Microphones
A single electret microphone may be used both for the analog front-end input (for recognition purposes) and as the
sound source for the Audio Wakeup unit. The current consumption and frequency response requirements are
different for the two uses, so two microphone input pads are provided: MICIN1 for the normal recognition input to
the analog front-end, and MICIN2 for the Audio Wakeup analog front end. A common microphone ground is used
for both the normal recognition analog front-end and the Audio Wakeup analog front end.
During normal recognition and Audio Wakeup operation, the microphone would typically be powered from a source
with an impedance in the range of 1-3 Kohms. If both the normal recognition and Audio Wakeup front ends are
used, they must be isolated from each other by capacitors and may share one microphone and microphone bias
circuit. The switching of the microphone input source is under program control. See schematic 1-3 for details on
this implementation.
The recommended value for the microphone filter capacitor (labeled “C5” in Schematic 1-3) is in the range of 33uF-
220uF. Using a capacitor at the upper end of this range will reduce low frequency noise. Low frequency noise on
the microphone input typically won’t affect recognition, but could affect the quality of speech playback when using
Record and Playback technology in an application. (see the “FluentChip Technology Library Manual” for more
information on Record and Playback) Typical low frequency noise sources include 60 Hz hum, “motor boating” or
相關PDF資料 |
PDF描述 |
|---|---|
| 80-0207-A | Speech And Music Processor |
| 80-0208-B | Speech And Music Processor |
| 80-0209-A | Speech And Music Processor |
| 80-0210-C | Speech And Music Processor |
| 80-0211-C | Speech And Music Processor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 80-0207-A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Speech And Music Processor |
| 80-0208-B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Speech And Music Processor |
| 800209-000 | 制造商:TE Connectivity 功能描述:55A0141-20-3/5/6/9 - Cable Rools/Shrink Tubing |
| 80-0209-A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Speech And Music Processor |
| 80020D | 功能描述:SCRDR DUAL MAT MAG KEY TP 3/8"X1 制造商:apex tool group 系列:* 零件狀態:在售 標準包裝:6 |
發布緊急采購，3分鐘左右您將得到回復。