- 您現在的位置：買賣IC網 > PDF目錄360549 > 7P160ATA2003C25 Flash Memory Card(160M位閃速存儲器卡) PDF資料下載
參數資料
| 型號： | 7P160ATA2003C25 |
| 英文描述： | Flash Memory Card(160M位閃速存儲器卡) |
| 中文描述： | 閃存卡（160米位閃速存儲器卡） |
| 文件頁數： | 6/66頁 |
| 文件大?。?/td> | 585K |
| 代理商： | 7P160ATA2003C25 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
7PxxxATA20xxC25
June 2000 Rev. 5 – ECO #12935
6
White Electronic Designs Corporation
(508) 366-5151
Battery voltage detection, Digital audio output, Disk active/slave present (BVD2, -SPKR, -DASP:
input/output):
In memory card mode, BVD2 outputs the battery voltage status in the card. This card has
no battery, so this output is high level constantly. In the I/O card mode, -SPKR is held High because this
card does not have digital audio output. In True IDE Mode -DASP is the Disk Active/Slave Present signal
in the Master/Slave handshake protocol.
Reset (RESET, -RESET: input):
By assertion of the RESET signal, all registers of this card are cleared
and the RDY/-BSY signal turns to high level. In True IDE Mode -RESET is the active low hardware reset
from the host.
Wait (-WAIT, IORDY: output):
This signal outputs low level for the purpose of delaying memory access
cycle or I/O access cycle. In True IDE Mode this output signal may be used as IORDY. As for this
controller, this output is high impedance state constantly.
Input acknowledge (-INPACK: output):
This signal is not used in the memory card mode. This signal
is asserted by this card when the card is selected and responding to an I/O read cycle at the address that is
on the address bus. This signal is used for the input data buffer control. In True IDE Mode this output
signal is not used and should be kept open at the host side.
Battery voltage detection, Status change, Pass diagnostic (BVD1, -STSCHG, -PDIAG: input/output):
In the memory card mode, BVD1 outputs the battery voltage status in the card. This card has no battery, so
this output is high level constantly. In the I/O card mode, -STSCHG is used for changing the status of the
Configuration status register in the Attribute area, while the card is set I/O card interface. In True IDE
Mode, -PDIAG is the Pass Diagnostic signal in the Master/Slave handshake protocol.
V
CC
voltage sense (-VS1, -VS2: output):
These signals are intended to notify the socket of the PC Card's
CIS V
CC
requirement. -VS1 is held low and -VS2 is nonconnected in this card.
Card select (-CSEL: input):
This signal is not used in the memory card mode and I/O card mode. This
internally pulled up signal is used to configure this device as a Master or a Slave when configured in the
True IDE Mode. When this pin is grounded, this device is configured as a Master. When the pin is open,
this device is configured as a Slave.
相關PDF資料 |
PDF描述 |
|---|---|
| 7P128 IDE 1511C25 | 2.5 Flash IDE Drives(2.5閃速存儲器IDE器件（128MB）) |
| 7P064 IDE 1511C25 | 2.5 Flash IDE Drives(2.5閃速存儲器IDE器件（64MB）) |
| 7P192ATA2500C25 | Flash Memory Card(192M位閃速存儲器卡) |
| 7P800ATA2514C25 | Flash Memory Card(800M位閃速存儲器卡) |
| 7P224ATA2500C25 | Flash Memory Card(224M位閃速存儲器卡) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 7P16-2T12-1 | 制造商:AUGAT COMPONENTS 功能描述: |
| 7P16-2T12-2 | 制造商:AUGAT COMPONENTS 功能描述: |
| 7P16-2T24-2 | 制造商:AUGAT COMPONENTS 功能描述: |
| 7P16-3T24-2 | 制造商:AUGAT COMPONENTS 功能描述: |
| 7P-19.200MBP-T | 功能描述:19.2MHz Clipped Sine Wave, CMOS TCXO Oscillator Surface Mount 2.7 V ~ 5.5 V 10mA 制造商:txc corporation 系列:7P 包裝:剪切帶（CT） 零件狀態:有效 類型:TCXO 頻率:19.2MHz 功能:- 輸出:削峰正弦波，CMOS 電壓 - 電源:2.7 V ~ 5.5 V 頻率穩定度:±280ppb 工作溫度:-40°C ~ 85°C 電流 - 電源（最大值）:10mA 等級:- 安裝類型:表面貼裝 大小/尺寸:0.197" 長 x 0.126" 寬（5.00mm x 3.20mm） 高度:0.065"（1.65mm） 封裝/外殼:6-SMD，無引線（DFN，LCC） 電流 - 電源（禁用）（最大值）:- 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。