參數資料
型號: 74ALVCH16543DGG:11
廠商: NXP Semiconductors
文件頁數: 7/20頁
文件大小: 0K
描述: IC TRANSCVR TRI-ST 16BIT 56SSOP
產品培訓模塊: Logic Packages
標準包裝: 35
系列: 74ALVCH
邏輯類型: 寄存收發器,非反相
元件數: 2
每個元件的位元數: 8
輸出電流高,低: 24mA,24mA
電源電壓: 1.2 V ~ 3.6 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 56-TFSOP(0.240",6.10mm 寬)
供應商設備封裝: 56-TSSOP
包裝: 管件
其它名稱: 74ALVCH16543DG
74ALVCH16543DG-ND
935262544112
1999 Nov 23
15
Philips Semiconductors
Product specication
16-bit D-type registered transceiver; 3-state
74ALVCH16543
SOLDERING
Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our
“Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering is not always suitable
for surface mount ICs, or for printed-circuit boards with
high population densities. In these situations reflow
soldering is often used.
Reow soldering
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
infrared/convection heating in a conveyor type oven.
Throughput times (preheating, soldering and cooling) vary
between 100 and 200 seconds depending on heating
method.
Typical reflow peak temperatures range from
215 to 250
°C. The top-surface temperature of the
packages should preferable be kept below 230
°C.
Wave soldering
Conventional single wave soldering is not recommended
for surface mount devices (SMDs) or printed-circuit boards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is preferred to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
For packages with leads on four sides, the footprint must
be placed at a 45
° angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time is 4 seconds at 250
°C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Manual soldering
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300
°C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320
°C.
相關PDF資料
PDF描述
74ALVCH16646DGG,11 IC TRANSCVR 16BIT N-INV 56TSSOP
74ALVCH16652DGG:11 IC 16BIT TXRX/REGISTER 56TSSOP
74ALVCH16832DGG,11 IC ADDRESS REGISTER DVR 64TSSOP
74ALVCHS162830DGB: IC ADDRESS DVR 18-36BIT 80TSSOP
74ALVCHT16835DGV:1 IC REGISTERED DVR 16BIT 56TVSOP
相關代理商/技術參數
參數描述
74ALVCH16543DGGRE4 功能描述:總線收發器 16B Reg Trnscvr RoHS:否 制造商:Fairchild Semiconductor 邏輯類型:CMOS 邏輯系列:74VCX 每芯片的通道數量:16 輸入電平:CMOS 輸出電平:CMOS 輸出類型:3-State 高電平輸出電流:- 24 mA 低電平輸出電流:24 mA 傳播延遲時間:6.2 ns 電源電壓-最大:2.7 V, 3.6 V 電源電壓-最小:1.65 V, 2.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-48 封裝:Reel
74ALVCH16543DGGRG4 功能描述:總線收發器 16B Reg Xceiver RoHS:否 制造商:Fairchild Semiconductor 邏輯類型:CMOS 邏輯系列:74VCX 每芯片的通道數量:16 輸入電平:CMOS 輸出電平:CMOS 輸出類型:3-State 高電平輸出電流:- 24 mA 低電平輸出電流:24 mA 傳播延遲時間:6.2 ns 電源電壓-最大:2.7 V, 3.6 V 電源電壓-最小:1.65 V, 2.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-48 封裝:Reel
74ALVCH16543DGGS 功能描述:IC TXRX 16BIT TRI-ST 56TSSOP 制造商:nexperia usa inc. 系列:74ALVCH 包裝:管件 零件狀態:在售 邏輯類型:收發器,非反相 元件數:2 每元件位數:8 輸入類型:- 輸出類型:推挽式 電流 - 輸出高,低:24mA,24mA 電壓 - 電源:1.2 V ~ 3.6 V 工作溫度:-40°C ~ 85°C(TA) 安裝類型:表面貼裝 封裝/外殼:56-TFSOP(0.240",6.10mm 寬) 供應商器件封裝:56-TSSOP 標準包裝:35
74ALVCH16543DGGY 功能描述:Transceiver, Non-Inverting 2 Element 8 Bit per Element Push-Pull Output 56-TSSOP 制造商:nxp semiconductors 系列:74ALVCH 包裝:帶卷(TR) 零件狀態:有效 邏輯類型:收發器,非反相 元件數:2 每元件位數:8 輸入類型:- 輸出類型:推挽式 電流 - 輸出高,低:24mA,24mA 電壓 - 電源:1.2 V ~ 3.6 V 工作溫度:-40°C ~ 85°C(TA) 安裝類型:表面貼裝 封裝/外殼:56-TFSOP(0.240",6.10mm 寬) 供應商器件封裝:56-TSSOP 標準包裝:2,000
74ALVCH16543DG-T 功能描述:總線收發器 16-BIT LATCH XCVR 3-S RoHS:否 制造商:Fairchild Semiconductor 邏輯類型:CMOS 邏輯系列:74VCX 每芯片的通道數量:16 輸入電平:CMOS 輸出電平:CMOS 輸出類型:3-State 高電平輸出電流:- 24 mA 低電平輸出電流:24 mA 傳播延遲時間:6.2 ns 電源電壓-最大:2.7 V, 3.6 V 電源電壓-最小:1.65 V, 2.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-48 封裝:Reel