參數資料
型號： 71M6542F-IGT/F
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： 模擬信號調理
英文描述： SPECIALTY ANALOG CIRCUIT, PQFP100
封裝： LEAD FREE, LQFP-100
文件頁數： 136/165頁
文件大?。?/td> 2208K
代理商： 71M6542F-IGT/F
72
2008–2011 Teridian Semiconductor Corporation
v1.1
4
RD
W
Indicates that EEDATA (SFR 0x9E) is to be filled with data from EEPROM.
3:0
CNT[3:0]
W
Specifies the number of clocks to be issued. Allowed values are 0
through 8. If RD=1, CNT bits of data are read MSB first, and right
justified into the low order bits of EEDATA. If RD=0, CNT bits are sent
MSB first to the EEPROM, shifted out of the MSB of EEDATA. If
CNT[3:0] is zero, SDATA simply obeys the HiZ bit.
The timing diagrams in Figure 22 through Figure 26 describe the 3-wire EEPROM interface behavior. All
commands begin when the EECTRL (SFR 0x9F) register is written. Transactions start by first raising the
DIO pin that is connected to CS. Multiple 8-bit or less commands such as those shown in Figure 22
through Figure 26 are then sent via EECTRL and EEDATA.
When the transaction is finished, CS must be lowered. At the end of a Read transaction, the EEPROM is
driving SDATA, but transitions to Hi-Z (high impedance) when CS falls. The firmware should then
immediately issue a write command with CNT=0 and HiZ=0 to take control of SDATA and force it to a
low-Z state.
Figure 22: 3-wire Interface. Write Command, HiZ=0.
Figure 23: 3-wire Interface. Write Command, HiZ=1
Figure 24: 3-wire Interface. Read Command.
SCLK (output)
BUSY (bit)
CNT Cycles (6 shown)
SDATA (output)
Write -- No HiZ
D2
D3
D4
D5
D6
D7
EECTRL Byte Written
INT5
SDATA output Z
(LoZ)
CNT Cycles (6 shown)
Write -- With HiZ
INT5
EECTRL Byte Written
SCLK (output)
BUSY (bit)
SDATA (output)
D2
D3
D4
D5
D6
D7
(HiZ)
(LoZ)
SDATA output Z
CNT Cycles (8 shown)
READ
D0
D1
D2
D3
D4
D5
INT5
D6
D7
EECTRL Byte Written
SCLK (output)
BUSY (bit)
SDATA (input)
SDATA output Z
(HiZ)
相關PDF資料
PDF描述
71M6542G-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6541G-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP64
71M6541F-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP64
71M6541D-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP64
71M6542F-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP100
相關代理商/技術參數
參數描述
71M6542F-IGTR/F 功能描述:計量片上系統 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel
71M6542FT-IGT/F 制造商:Maxim Integrated Products 功能描述:1-PHASE SOC 128KB WITH PREC TEMP SENSOR - Rail/Tube
71M6542FT-IGTR/F 制造商:Maxim Integrated Products 功能描述:1-PHASE SOC, 64KB FLASH, PRES TEMP SENSOR - Tape and Reel
71M6542G 制造商:未知廠家 制造商全稱:未知廠家 功能描述:71M6541D/71M6541F/71M6541G/71M6542F/71M6542G 是 TeridianTM 的第4 代高集成度單相電表SoC
71M6542G-IGT/F 功能描述:計量片上系統 - SoC 1-Phase Metering SOC with 128KB Flash RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*