參數資料
型號： 71M6513H-IGT/F
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： 模擬信號調理
英文描述： SPECIALTY ANALOG CIRCUIT, PQFP100
封裝： LEAD FREE, LQFP-100
文件頁數： 92/104頁
文件大?。?/td> 1390K
代理商： 71M6513H-IGT/F
71M6513/71M6513H
3-Phase Energy Meter IC
DATA SHEET
AUGUST 2011
Page: 88 of 104
2005-2011 Teridian Semiconductor Corporation
A Maxim Integrated Products Brand
Figure 39: External Components for RESETZ
Connecting the V3 Pin
The following should be noted when connecting the V3 pin:
1)
If the V3 pin is unused it should be left floating or terminated to the VREF pin.
2)
If the V3 pin is used as a comparator input the digital input voltage applied to V3 should be limited to VBIAS
±0.9V.
3)
If the V3 pin is used either as an auxiliary analog input, and temperature measurements are made and evaluated
using the alternate multiplexer cycle, the V3 input voltage range must be restricted to VBIAS
±0.9 V (i.e. 0.6 V to 2.4
V). Otherwise, the TEMP or V3 measurement could be inaccurate. This precaution is particularly important for
customers who are using the TEMP samples for temperature compensation, especially with the 71M6513H devices.
Connecting a Battery
Many meter manufacturers assemble the meter PCB with the 71M6513 IC and the other electronic components first and then
join the meter PCB with the meter enclosure, sensors and other main components separately at a later production step.
Typically, programming, final test (ATE), and calibration are performed after this second step.
The following production sequence is strongly recommended:
1)
During PCB assembly, when adding/inserting the battery, the board supply voltage (V3P3A, V3P3D) should be active
(i.e. at 3.3 VDC), which can be achieved by briefly connecting the battery to V3P3A/V3P3D through a jumper wire.
After the battery is inserted with the board power active, the jumper wire should be removed.
2)
The battery should then remain connected through factory test (ATE), time on the shelf and shipment.
In cases where it is not feasible to power V3P3A/V3P3D while inserting the battery, it is recommended to isolate the battery in
its holder using a removable piece of Kapton tape or other isolating material. This isolation should then be removed once the
meter is fully powered during the calibration and test process.
R
1
RESETZ
71M6513
DGND
V3P3
R
2
V3P3
Pushbutton
C
1
200
Ω
1nF
10
Ω
R
1
RESETZ
71M6513
DGND
V3P3
R
2
V3P3
Pushbutton
C
1
200
Ω
1nF
10
Ω
相關PDF資料
PDF描述
71M6513H-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6513-IGT/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6515H-IGTW/F SPECIALTY ANALOG CIRCUIT, PQFP64
71M6515H-IGTWR/F SPECIALTY ANALOG CIRCUIT, PQFP64
71M6515H-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP64
相關代理商/技術參數
參數描述
71M6513H-IGTR/F 功能描述:計量片上系統 - SoC 3-Phase Energy Meter I/C RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel
71M6513H-IGTR/F1 功能描述:計量片上系統 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel
71M6513-IEL 制造商:未知廠家 制造商全稱:未知廠家 功能描述:71M6513
71M6513-IEL/F 功能描述:計量片上系統 - SoC 3-Phase Energy Meter I/C RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel
71M6513-IELR/F 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC 3-Phase Energy Meter I/C
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*