- 您現在的位置：買賣IC網 > PDF目錄97839 > 71M6513H-IGT/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF資料下載
參數資料
| 型號： | 71M6513H-IGT/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封裝： | LEAD FREE, LQFP-100 |
| 文件頁數： | 48/104頁 |
| 文件大?。?/td> | 1390K |
| 代理商： | 71M6513H-IGT/F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁當前第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁
71M6513/71M6513H
3-Phase Energy Meter IC
DATA SHEET
AUGUST 2011
Page: 48 of 104
2005-2011 Teridian Semiconductor Corporation
A Maxim Integrated Products Brand
out in 35 cycles and contains a leading flag bit. Figure 13 in the System Timing Section illustrates the RTM output format. RTM
is low when not in use.
SSI Interface: A high-speed serial interface with handshake capability is available to send a contiguous block of CE data to an
external data logger or DSP. The block of data, configurable as to location and size, is sent starting 1 cycle of 32kHz before
each CE code pass begins. If the block of data is big enough that transmission has not completed when the code pass begins,
it will complete during the CE code pass with no timing impact to the CE or the serial data. In this case, care must be taken
that the transmitted data is not modified unexpectedly by the CE. The SSI interface is enabled by the SSI_EN bit and consists
of SCLK, SSDATA, and SFR as outputs and, optionally, SRDY as input. The interface is compatible with 16bit and 32bit
processors. The operation of each pin is as follows:
SCLK is the serial clock. The clock can be 5MHz or 10MHz, as specified by the SSI_10M bit. The SSI_CKGATE bit controls
whether SCLK runs continuously or is gated off when no SSI activity is occurring. If SCLK is gated, it will begin 3 cycles before
SFR rises and will persist 3 cycles after the last data bit is output.
The pins used for the SSI are multiplexed with the LCD segment outputs, as shown in Table 58. Thus, the LCD should be
disabled when the SSI is in use.
SSI Signal
LCD Segment
Output Pin
SCLK
SEG3
SSDATA
SEG4
SFR
SEG5
SRDY
SEG6
Table 58: SSI Pin Assignment
SRDY is an optional handshake input that indicates that the DSP or data-logging device is ready to receive data. SRDY must
be true (the polarity of SRDY is selectable with SSI_FPOL) to enable SFR to rise and initiate the transfer of the next field. It is
expected that SRDY changes state on the rising edges of SCLK. If SRDY is not true when the SSI port is ready to transmit the
next field, transmission will be delayed until it is. SRDY is ignored except at the beginning of a field transmission. If SRDY is
not enabled (by SSI_RDYEN), the SSI port will behave as if SRDY is always true.
SSDATA is the serial output data. SSDATA changes on the rising edge of SCLK and outputs the contents of a block of CE
RAM words starting with address SSI_STRT and ending with SSI_END. The words are output MSB first.
The field size is set with the SSI_FSIZE register: 0 entire data block, 1-8 bit fields, 2-16 bit fields, 3-32 bit fields. The polarity of
the SFR pulse can be inverted with SSI_FPOL (SSI_FPOL = 0 SRDY high-active). If SRDY does not delay it, the first SFR
pulse in a frame will rise on the third SCLK after MUX_SYNC (or the fourth SCLK if 10MHz). MUX_SYNC can be used to
synchronize the fields arriving at the data logger or DSP.
相關PDF資料 |
PDF描述 |
|---|---|
| 71M6513H-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6513-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6515H-IGTW/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 71M6515H-IGTWR/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 71M6515H-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 71M6513H-IGTR/F | 功能描述:計量片上系統 - SoC 3-Phase Energy Meter I/C RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6513H-IGTR/F1 | 功能描述:計量片上系統 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6513-IEL | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:71M6513 |
| 71M6513-IEL/F | 功能描述:計量片上系統 - SoC 3-Phase Energy Meter I/C RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6513-IELR/F | 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC 3-Phase Energy Meter I/C |
發布緊急采購，3分鐘左右您將得到回復。