- 您現在的位置：買賣IC網 > PDF目錄351971 > 3403.0018.11 Fuse PDF資料下載
參數資料
| 型號： | 3403.0018.11 |
| 元件分類： | 保險絲 |
| 英文描述： | Fuse |
| 中文描述： | 保險絲 |
| 文件頁數： | 55/65頁 |
| 文件大?。?/td> | 2586K |
| 代理商： | 3403.0018.11 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁當前第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁
Schurter, Inc. Phone 707-778-6311 Fax 707-778-6401 E-mail: info@schurterinc.com Website http://www.schurterinc.com
161
Surge Tolerant Fuses
2. UL1459/1950
Test circuit
Fig. 4
Test 1:
The fuse in the test current circuit is loaded with a test current
of ISC = 40 A .
The AC 600 V / 50 Hz source voltage is applied for a total
of 1.5 sec.
Requirement: The fuse shall interrupt the circuit.
Test 2:
The fuse in the test current circuit is loaded with a test current
of ISC = 7 A .
The AC 600 V / 50 Hz source voltage is applied for a total
of 5 sec.
Requirement: The fuse shall interrupt the circuit.
Test 3
The fuse in the test current circuit is loaded with a test current
of ISC = 2,2 A .
The AC 600 V / 50Hz source voltage is applied for at least
30 minutes, or until stable thermal conditions are achieved
in the telecom unit or until the fuse interrupts the circuit.
This test is performed together with the equipment in which the
fuse is installed.
Fuse
A
C
600
V
RD
t = 1,5 s/5 s/ 30 Min.
I sc = 40 A/7 A/2.2. A
3. GR 1089
Test circuit
Test:
1. The pulse amplitude (generator no-load) is set to 1000 V
and the pulse shape to 10 s / 1000 s.
2. The pulse current Ipuls is set to the value Ipuls max. stated in
the data sheet with limiting resistor RD.
3. Test mode: 50 single pulses, at an interval of 60 sec.
alternating polarity.
Requirement: The fuse shall not interrupt the circuit.
5) Note: With a charge voltage of UC = 1000 V, the standar-
dized pulse generator in Fig. 5 supplies a maximum pulse
current Ipuls = 14 A, providing the current limiting resistor is
RD = 0. The shunt RM for the current monitoring has a very
low resistance and has no notable influence to the current
amplitude. This means that the data sheet current 14 A (5) does
not represent the maximum permissible pulse amplitude of the
fuse in question, but the maximum current amplitude which can
be supplied by the pulse generator. If a max. current higher
than 14 A is to be expected in a circuit, the
I2t- values of the fuse can be calculated using the formula I2t =
0,72 x i2peak x t2, as a good approximation in order that the
selected fuse can accept the expected current pulse without
interrupting the circuit.
Fig. 5
Pulse current
Generator no load
t1=10s
t2=1000s
50%
I puls
max.
Ipuls
RD
U
c
=
1000
V
.
+
20 F
267 H
50 k
RM
68
Fuse
相關PDF資料 |
PDF描述 |
|---|---|
| 38E04A230 | 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit |
| 3VC32H100EV-1.5MHZ | Crystal Oscillator |
| 3VC13H50CV-2MHZ | Crystal Oscillator |
| 3VCPL15FT160 | 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit |
| 3VCPL25FT160 | 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 3403001824 | 制造商:Schurter Electronic Components 功能描述: |
| 340-3002 | 功能描述:3M ULTRAFIT SILICONE COR 制造商:3m 系列:* 零件狀態:在售 標準包裝:1 |
| 340-300A | 制造商:LG Corporation 功能描述:BRACKET |
| 340-300B | 制造商:LG Corporation 功能描述:BRACKET |
| 340-307A | 制造商:LG Corporation 功能描述:BRACKETFBT,(CV430) |
發布緊急采購，3分鐘左右您將得到回復。