參數資料
型號： 33888
廠商： Motorola, Inc.
英文描述： Quad High-Side and Octal Low-Side Switch for Automotive
中文描述： 四高邊和八路低端汽車開關
文件頁數： 25/32頁
文件大小： 667K
代理商： 33888
MOTOROLA ANALOG INTEGRATED CIRCUIT DEVICE DATA
33888
25
Figure 6. Low-Side Output OFF Open Load Detection
Overcurrent Fault Requirements: Low-Side Output
An overcurrent condition is defined as any current value
greater than I
LIM
(500 mA minimum value for LS5, LS7, LS9,
LS11, and 800 mA minimum value for LS4, LS6, LS8, LS10).
The status of the corresponding bit in the CLOCCR register
determines whether a specific output shuts down or continues
to operate in an analog current limited mode until either the
overcurrent condition is removed or the thermal shutdown limit
is reached (
Figure 7
, page 26). If the overcurrent shutdown
mode is disabled, the fault reporting is disabled as well.
For the low-side output of interest, if a D11:D4 bit was set to
a logic [1] in the OLCR register, the overcurrent protection
shutdown circuitry will be enabled for that output. When a low-
side output is commanded ON either from the SPI or the ILS
terminal, the drain of the low-side driver will be monitored for a
voltage greater than the fault detection threshold (3.0 V typical).
If the drain voltage exceeds this threshold, a timer will start and
the output will be turned off and a fault latched in the status
register after the timeout expires. The faulted output can be
retried only by commanding the output OFF and back ON either
through the SPI or the ILS terminal, depending on the logic
configuration. If the fault is gone, the retried output will return to
normal operation and the status register can be cleared on a
rising edge of
CS
. If the fault remains, the retried output will
latch off after the fault timer expires and the fault bit will remain
set in the status register.
For the low-side output of interest, if a D11:D4 bit was set to
a logic [0] in the OLCR register, the output experiencing an
overcurrent condition is not disabled until an overtemperature
fault threshold has been reached. The specific output goes into
an analog current limit mode of operation, I
LIM
. The 33888 uses
overtemperature shutdown to protect all outputs in this mode of
operation. If the overcurrent condition is removed before the
output has reached its overtemperature limit, the output will
function as if no fault has occurred.
Note that each pair of low-side drivers, LS4:LS5, LS6:LS7,
LS8:LS9, and LS10:LS11, consists of a 500 mA and a 800 mA
output. Each pair of outputs shares ground bondwires. The
bondwires are not rated to handle both outputs in current limit
mode simultaneously.
Overcurrent Fault Requirements: High-Side Output
For the high-side output of interest, the output current is
limited to one of four levels depending on the type of high-side
output, the amount of time that has elapsed since the output
was switched on, and the state of the CLOCCR register.
Assuming that bits D3:D0 of the CLOCCR register are at
logic [0], the current limit levels of the outputs will be initially at
their peak levels as specified by the I
LIM(PK)HS[0:3]
. After the
high-side output is switched on, the peak current timer starts.
After a period of time t
PCT
, the current limit level changes to the
sustain levels I
LIMSUSHS[x,x]
.
For the high-side output of interest, if a D3:D0 bit of the
CLOCCR is at logic [1], then the assigned output will only
current limit at the sustain level specified by I
LIMSUSHS[x,x]
.
Current is limited until the overtemperature circuitry shuts
OFF the device. The device turns ON automatically when the
temperature fails below the T
LIM(HYS)
. This cycle continues
indefinitely until action is taken by the master to shut the
output(s) OFF.
Reverse Battery Requirements
The low-side and high-side outputs survive the application of
reverse battery as low as -16 V.
Ground Disconnect Protection
In the event that the 33888 ground is disconnected from load
ground, the device protects itself and safely turns OFF the
outputs, regardless of the state of the output at the time of
disconnection.
OUTPUT
V
THRES
MOSFET
R
L
V
PWR
LOW = Logic 0
50 mA
V
OFD(THRES)LS
2.0 V–4.0 V
–
+
33888
V
PWR
R
L
OUT
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料
PDF描述
33888A Quad High-Side and Octal Low-Side Switch for Automotive
338FP-M Versatile Miniature Switch, High Performance
33981 High-Frequency, High-Current, Self-Protected High-Side Switch (4.0 mз up to 60 kHz)
33984 Dual Intelligent High-Current Self-Protected Silicon High-Side Switch (4.0 mз)
33991 Gauge Driver Integrated Circuit
相關代理商/技術參數
參數描述
33888A 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Quad High-Side and Octal Low-Side Switch for Automotive
33889 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:System Basis Chip with Low Speed Fault Tolerant CAN Interface
338-894 制造商:Johnson Electric / Saia-Burgess 功能描述:16mm tool kit mounting spanners
338895 制造商:CORNING CABLE SYSTEMS 功能描述:CORNING-C 95-200-42 SC 8.3/125 SM UNICAM CONN
338898 制造商:CORNING CABLE SYSTEMS 功能描述:ST 62.5/125 UNICAM CONNECTOR COMPOSITE FERRULE SINGLE PACK
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*