參數資料
型號： 29LV160B
廠商： Macronix International Co., Ltd.
英文描述： 16M-BIT [2Mx8/1Mx16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY
中文描述： 1,600位[2Mx8/1Mx16] CMOS單電壓3V時僅閃存
文件頁數： 14/63頁
文件大?。?/td> 762K
代理商： 29LV160B
14
P/N:PM1041
MX29LV160BT/BB
REV. 1.2, JUL. 01, 2004
R
READING ARRAY DATA
The device is automatically set to reading array data
after device power-up. No commands are required to re-
trieve data. The device is also ready to read array data
after completing an Automatic Program or Automatic
Erase algorithm.
After the device accepts an Erase Suspend command,
the device enters the Erase Suspend mode. The sys-
tem can read array data using the standard read tim-
ings, except that if it reads at an address within erase-
suspended sectors, the device outputs status data. Af-
ter completing a programming operation in the Erase
Suspend mode, the system may once again read array
data with the same exception. See erase Suspend/Erase
Resume Commands
”
for more information on this mode.
The system must issue the reset command to re-en-
able the device for reading array data if Q5 goes high, or
while in the "read silicon-ID" and "sector protect verify"
mode. See the "Reset Command" section, next.
RESET COMMAND
Writing the reset command to the device resets the de-
vice to reading array data. Address bits are don't care
for this command.
The reset command may be written between the se-
quence cycles in an erase command sequence before
erasing begins. This resets the device to reading array
data. Once erasure begins, however, the device ignores
reset commands until the operation is complete.
The reset command may be written between the se-
quence cycles in a program command sequence before
programming begins. This resets the device to reading
array data (also applies to programming in Erase Sus-
pend mode). Once programming begins, however, the
device ignores reset commands until the operation is
complete.
The reset command may be written between the se-
quence cycles in an Automatic Select command se-
quence. Once in the Automatic Select mode, the reset
command must be written to return to reading array data
(also applies to Automatic Select during Erase Suspend).
If Q5 goes high during a program or erase operation,
writing the reset command returns the device to reading
array data (also applies during Erase Suspend).
Pins
A0
A1
Q15~Q8 Q7
Q6
Q5
Q4
Q3
Q2 Q1
Q0
Code(Hex)
Manufacturer code
Word
VIL
VIL
00H
1
1
0
0
0
0
1
0
00C2H
Byte
VIL
VIL
X
1
1
0
0
0
0
1
0
C2H
Device code
Word
VIH
VIL
22H
1
1
0
0
0
1
0
0
22C4H
for MX29LV160BT
Byte
VIH
VIL
X
1
1
0
0
0
1
0
0
C4H
Device code
Word
VIH
VIL
22H
0
1
0
0
1
0
0
1
2249H
for MX29LV160BB
Byte
VIH
VIL
X
0
1
0
0
1
0
0
1
49H
Sector Protection
Word
X
VIH
X
0
0
0
0
0
0
0
1
01H (Protected)
Verification
Byte
X
VIH
X
0
0
0
0
0
0
0
0
00H (Unprotected)
TABLE 7. SILICON ID CODE
相關PDF資料
PDF描述
29LV160B 16 Megabit (2 M x 8-Bit/1 M x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory
29LV160C-55R 16M-BIT [2Mx8/1Mx16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY
29LV160C-70 16M-BIT [2Mx8/1Mx16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY
29LV160C-90 16M-BIT [2Mx8/1Mx16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY
29LV320BTC-70 32 BIT 4M X 8 / 2M X 16 ] SINGLE VOLTAGE 3V ONLY FLASH MEMORY
相關代理商/技術參數
參數描述
29LV160BE 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16M (2M X 8/1M X 16) BIT
29LV160BT-90V 制造商: 功能描述: 制造商:undefined 功能描述:
29LV160C-55R 制造商:MCNIX 制造商全稱:Macronix International 功能描述:16M-BIT [2Mx8/1Mx16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY
29LV160C-70 制造商:MCNIX 制造商全稱:Macronix International 功能描述:16M-BIT [2Mx8/1Mx16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY
29LV160C-90 制造商:MCNIX 制造商全稱:Macronix International 功能描述:16M-BIT [2Mx8/1Mx16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*