- 您現在的位置：買賣IC網 > PDF目錄368900 > 255D227X0004D2T040 (Vishay Intertechnology,Inc.) Organic Polymer, Low ESR, Tantalum Capacitors Commercial, Surface Mount Capacitors for Switch Mode Power Supplies and Converters PDF資料下載
參數資料
| 型號： | 255D227X0004D2T040 |
| 廠商： | Vishay Intertechnology,Inc. |
| 英文描述： | Organic Polymer, Low ESR, Tantalum Capacitors Commercial, Surface Mount Capacitors for Switch Mode Power Supplies and Converters |
| 中文描述： | 有機聚合物，低ESR，商業鉭電容，表面貼裝電容器開關電源和轉換器 |
| 文件頁數： | 5/6頁 |
| 文件大?。?/td> | 177K |
| 代理商： | 255D227X0004D2T040 |
Document Number: 40052
Revision 04-Feb-03
www.vishay.com
6
Type 255D
Vishay Sprague
4.
Recommended rated working voltage
guidelines:
5.
Printed Circuit Board Materials
: The 255D is
compatible with commonly used printed circuit board
materials (alumina substrates, FR4, FR5, G10, PTFE-
fluorocarbon and porcelainized steel).
6.
Attachment:
6.1
Solder Paste:
The recommended thickness of the
solder paste after application is .007"
±
.001" [.178mm
±
0.025mm]. Care should be exercised in selecting
the solder paste. The metal purity should be high as
practical. The flux (in the paste) must be active enough
to remove the oxides formed on the metallization prior
to the exposure to soldering heat. In practice this can
be aided by extending the solder preheat time at
temperatures below the liquidous of the solder.
6.2
Soldering:
Capacitors can be attached by
conventional soldering techniques - vapor phase,
infrared reflow, wave soldering and hot plate methods.
The Soldering Profile chart shows maximum
recommended mended time/temperature conditions for
soldering. Attachment with a soldering iron is not
recommended due to the difficulty of controlling
temperature and time at temperature. If hand soldering
is necessary, the soldering iron must never come in
contact with the capacitor.
APPLICATION VOLTAGE
(V)
RECOMMENDED
CAPACITOR VOLTAGE
RATING (V)
2.5
4.0
6.0
4.0
6.3
10.0
9.
Cleaning (Flux Removal) After Soldering:
The 255D
is compatible with all commonly used solvents such as
TES, TMS, Prelete, Chlorethane, Terpene and aqueous
cleaning media. However, CFC/ODS products are not
used in the production of these devices and are not
recommended. Solvents containing methylene chloride
or other epoxy solvents should be avoided since these
will attack the epoxy encapsulation material.
9.1
When using ultrasonic cleaning, the board may
resonate if the output power is too high. This vibration
can cause cracking or a decrease in the adherence-
of the termination. DO NOT EXCEED 9W/L @ 40kHz
for 2 minutes.
8.
Recommended Mounting Pad Geometries
: Proper
mounting pad geometries are essential for successful
solder connections. These dimensions are highly
process sensitive and should be designed to minimize
component rework due to unacceptable solder joints.
The dimensional configurations shown are the
recommended pad geometries for both wave and reflow
soldering techniques. These dimensions are intended
to be a starting point for circuit board designers and
may be fine tuned if necessary based upon the
peculiarities of the soldering process and/or circuit
board design.
REFLOW SOLDER PADS*
in inches [millimeters)
Case
Code
D
Separation
(C)
Pad
Metallization
(B)
Width
(A)
.118
[3.0]
.175
[4.45]
.106
[2.70]
Time (Seconds)
T
300
250
200
150
100
50
0
300
250
200
150
100
50
0
240
°
C Typical
130
°
C Typical
0
50
100
150
200
250
D
C
B
E
A
REFLOW SOLDERING PROFILE
GUIDE TO APPLICATION
相關PDF資料 |
PDF描述 |
|---|---|
| 255D227X0004D2T045 | Organic Polymer, Low ESR, Tantalum Capacitors Commercial, Surface Mount Capacitors for Switch Mode Power Supplies and Converters |
| 255D227X0004D2T055 | Organic Polymer, Low ESR, Tantalum Capacitors Commercial, Surface Mount Capacitors for Switch Mode Power Supplies and Converters |
| 255D227X0004D2W | Organic Polymer, Low ESR, Tantalum Capacitors Commercial, Surface Mount Capacitors for Switch Mode Power Supplies and Converters |
| 255D157X06R3D2T055 | Organic Polymer, Low ESR, Tantalum Capacitors Commercial, Surface Mount Capacitors for Switch Mode Power Supplies and Converters |
| 255D157X06R3D2W045 | Organic Polymer, Low ESR, Tantalum Capacitors Commercial, Surface Mount Capacitors for Switch Mode Power Supplies and Converters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 255D227X0004D2T045 | 功能描述:鉭質電容器-SMD聚合物 220uF 4volts 20% ESR 45 D case RoHS:否 制造商:Kemet 電容:33 uF 電壓額定值:50 V ESR:40 mOhms 容差:20 % 工作溫度范圍: 外殼代碼 - in:2917 外殼代碼 - mm:7343 高度:4 mm 制造商庫存號:X Case 系列:T543 產品: 封裝:Reel |
| 255D227X0004D2T055 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Organic Polymer, Low ESR, Tantalum Capacitors Commercial, Surface Mount Capacitors for Switch Mode Power Supplies and Converters |
| 255D227X0004D2W | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Organic Polymer, Low ESR, Tantalum Capacitors Commercial, Surface Mount Capacitors for Switch Mode Power Supplies and Converters |
| 255D227X0004D2W040 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Organic Polymer, Low ESR, Tantalum Capacitors Commercial, Surface Mount Capacitors for Switch Mode Power Supplies and Converters |
| 255D227X0004D2W045 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Organic Polymer, Low ESR, Tantalum Capacitors Commercial, Surface Mount Capacitors for Switch Mode Power Supplies and Converters |
發布緊急采購，3分鐘左右您將得到回復。