參數資料
型號: 255D227X0004D2T040
廠商: Vishay Intertechnology,Inc.
英文描述: Organic Polymer, Low ESR, Tantalum Capacitors Commercial, Surface Mount Capacitors for Switch Mode Power Supplies and Converters
中文描述: 有機聚合物,低ESR,商業鉭電容,表面貼裝電容器開關電源和轉換器
文件頁數: 4/6頁
文件大?。?/td> 177K
代理商: 255D227X0004D2T040
www.vishay.com
5
Type 255D
Vishay Sprague
Document Number: 40052
Revision 04-Feb-03
PERFORMANCE CHARACTERISTICS
(Continued)
1.
A-C Ripple Current:
The maximum allowable ripple
current shall be determined from the formula:
where,
P = Power Dissipation in Watts @ + 25
°
C as given in
the table in Paragraph Number 5 (Power
Dissipation).
R
ESR
=The capacitor Equivalent Series Resistance at the
specified frequency.
2.
A-C Ripple Voltage:
The maximum allowable ripple
voltage shall be determined from the formula:
or, from the formula:
where,
P = Power Dissipation in Watts @ + 25
°
C as given in
the table in Paragraph Number 5 (Power
Dissipation).
R
ESR
=The capacitor Equivalent Series Resistance at the
specified frequency.
Z = The capacitor impedance at the specified frequency.
2.1
The sum of the peak AC voltage plus the DC voltage
shall not exceed the DC voltage rating of the capacitor.
V
rms
= I
rms
x Z
2.4
Power Dissipation
: Power dissipation will be affected
by the heat sinking capability of the mounting surface.
Non-sinusoidal ripple current may produce heating
effects which differ from those shown. It is important
that the equivalent
Irms
value be established when
calculating permissible operating levels. (Power
Dissipation calculated using +25
°
C temperature rise).
I
rms
=
P
R
ESR
V
rms
=
P
R
ESR
CASE CODE
MAXIMUM PERMISSIBLE
POWER DISSIPATION
@ + 25C (Watts) IN FREE AIR
D
0.150
TEMPERATURE
DERATING FACTOR
+25
°
C
+ 85
°
C
+ 105
°
C
1.0
0.9
0.4
10.
Solderability:
Capacitors will meet the solderability
requirements of (MIL-STD-202, method 208),
ANSI/J-STD-002, Test B.
11.
Resistance to Solder Heat:
Capacitors will with stand
reflow soldering @ + 240
°
C + 5
°
C for 10 seconds max.
Capacitors should be allowed to remain at ambient
conditions for a period of up to 24 hours prior to
electrical measurements.
11.1
Following the resistance to solder heat test,
capacitance, be within
±
20% of the initial value, the
dissipation factor and the DC leakage current shall not
exceed the initial value.
12.
Terminal Strength:
Per IEC-384-3, minimum of 3N
shear force.
13.
Flammability:
Encapsulant materials meet UL94 VO
with an oxygen index of 32%.
GUIDE TO APPLICATION
14.
Capacitor Failure Mode:
The predominant failure
mode for solid tantalum capacitors is increased leak-
age current resulting in a shorted circuit. Capacitor
failure may result from excess forward or reverse DC
voltage, surge current, ripple current, thermal shock
or excessive temperature. The increase in leakage is
caused by a breakdown of the Ta2O5 dielecric. For
additional information on leakage failure of solid tan-
talum chip capacitors, refer to Vishay Sprague Tech-
nical Paper, “Leakage Failure Mode in Solid Tantalum
Chip Capacitors.”
15 Humidity Test:
Capacitors shall withstand 500 hours at
+ 60
°
C, 90% to 95% relative humidity, with no voltage
applied.
15.1
Following the humidity test, capacitance change shall
not exceed -20% to + 40% of the initial value, dissipation
factor shall not exceed 150% of the initial requirement;
leakage current shall not exceed 0.1CV (9uA).
2.2
The sum of the negative peak AC voltage plus the
applied DC voltage shall not allow a voltage reversal
exceeding 10% of the DC working voltage at + 25
°
C.
Temperature Derating
: If these capacitors are to be
operated at temperatures above + 25
°
C, the
permissible rms ripple current or voltage shall be
calculated using the derating factors as shown:
2.3
3.
Reverse Voltage:
These capacitors are capable of
withstanding peak voltages in the reverse direction
equal to 10% of the DC rating at + 25
°
C, 5% of the DC
rating at + 85
°
C and 1% of the DC rating at +105
°
C.
相關PDF資料
PDF描述
255D227X0004D2T045 Organic Polymer, Low ESR, Tantalum Capacitors Commercial, Surface Mount Capacitors for Switch Mode Power Supplies and Converters
255D227X0004D2T055 Organic Polymer, Low ESR, Tantalum Capacitors Commercial, Surface Mount Capacitors for Switch Mode Power Supplies and Converters
255D227X0004D2W Organic Polymer, Low ESR, Tantalum Capacitors Commercial, Surface Mount Capacitors for Switch Mode Power Supplies and Converters
255D157X06R3D2T055 Organic Polymer, Low ESR, Tantalum Capacitors Commercial, Surface Mount Capacitors for Switch Mode Power Supplies and Converters
255D157X06R3D2W045 Organic Polymer, Low ESR, Tantalum Capacitors Commercial, Surface Mount Capacitors for Switch Mode Power Supplies and Converters
相關代理商/技術參數
參數描述
255D227X0004D2T045 功能描述:鉭質電容器-SMD聚合物 220uF 4volts 20% ESR 45 D case RoHS:否 制造商:Kemet 電容:33 uF 電壓額定值:50 V ESR:40 mOhms 容差:20 % 工作溫度范圍: 外殼代碼 - in:2917 外殼代碼 - mm:7343 高度:4 mm 制造商庫存號:X Case 系列:T543 產品: 封裝:Reel
255D227X0004D2T055 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Organic Polymer, Low ESR, Tantalum Capacitors Commercial, Surface Mount Capacitors for Switch Mode Power Supplies and Converters
255D227X0004D2W 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Organic Polymer, Low ESR, Tantalum Capacitors Commercial, Surface Mount Capacitors for Switch Mode Power Supplies and Converters
255D227X0004D2W040 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Organic Polymer, Low ESR, Tantalum Capacitors Commercial, Surface Mount Capacitors for Switch Mode Power Supplies and Converters
255D227X0004D2W045 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Organic Polymer, Low ESR, Tantalum Capacitors Commercial, Surface Mount Capacitors for Switch Mode Power Supplies and Converters