參數資料
型號: 24LC41P
廠商: Microchip Technology Inc.
英文描述: 1K/4K 2.5V Dual Mode, Dual Port I2C⑩ Serial EEPROM
中文描述: 1K/4K 2.5V的雙模式,雙端口串行EEPROM的I2C⑩
文件頁數: 4/18頁
文件大小: 150K
代理商: 24LC41P
24LC41
DS21140F-page 4
2004 Microchip Technology Inc.
2.0
FUNCTIONAL DESCRIPTION
2.1
DDC Monitor Port
The DDC Monitor Port operates in two modes, the
Transmit-only mode and the Bidirectional mode. There
is a separate 2-wire protocol to support each mode,
each having a separate clock input and sharing a
common data line (DSDA). The device enters the
Transmit-only mode upon power-up. In this mode, the
device transmits data bits on the DSDA pin in response
to a clock signal on the VCLK/DWP pin. The device will
remain in this mode until a valid high-to-low transition is
placed on the DSCL input. When a valid transition on
DSCL is recognized, the device will switch into the
Bidirectional mode. The only way to switch the device
back to the Transmit-only mode is to remove power
from the device.
2.2
Transmit-Only Mode
The device will power-up in the Transmit-only mode.
This mode supports a unidirectional 2-wire protocol for
transmission of the contents of the memory array. This
device requires that it be initialized prior to valid data
being sent in the Transmit-only mode (
Section 2.3
“Initialization Procedure”
). In this mode, data is
transmitted on the DSDA pin in 8-bit bytes, each
followed by a ninth, null bit (Figure 2-1). The clock
source for the Transmit-only mode is provided on the
VCLK/DWP pin, and a data bit is output on the rising
edge on this pin. The eight bits in each byte are trans-
mitted by Most Significant bit first. Each byte within the
memory array will be output in sequence. When the last
byte in the memory array is transmitted, the output will
wrap around to the first location and continue. The
Bidirectional mode Clock (DSCL) pin must be held high
for the device to remain in the Transmit-only mode.
2.3
Initialization Procedure
After V
CC
has stabilized, the device will be in the
Transmit-only mode. Nine clock cycles on the VCLK/
DWP pin must be given to the device for it to perform
internal sychronization. During this period, the DSDA
pin will be in a high-impedance state. On the rising
edge of the tenth clock cycle, the device will output the
first valid data bit which will be the Most Significant bit
of a byte. The device will power-up at an indeterminate
byte address (Figure 2-2).
FIGURE 2-1:
TRANSMIT-ONLY MODE
FIGURE 2-2:
DEVICE INITIALIZATION
DSCL
DSDA
VCLK/DWP
T
VAA
T
VAA
Bit 1 (LSB)
Null Bit
Bit 1 (MSB)
Bit 7
T
VLOW
T
VHIGH
T
VAA
T
VAA
Bit 8
Bit 7
High-impedance for 9 clock cycles
T
VPU
1
2
8
9
10
11
SCL
SDA
VCLK/DWP
V
CC
相關PDF資料
PDF描述
24LC41 1K/4K 2.5V Dual Mode, Dual Port I 2 C Serial EEPROM
24LC41-IP 1K/4K 2.5V Dual Mode, Dual Port I 2 C Serial EEPROM
24LC41-P 1K/4K 2.5V Dual Mode, Dual Port I 2 C Serial EEPROM
24LC61-IP 1K/2K Software Addressable I 2 C ⑩ Serial EEPROM
24LCS61 1K/2K Software Addressable I 2 C ⑩ Serial EEPROM
相關代理商/技術參數
參數描述
24LC512/S16K 制造商:Microchip Technology Inc 功能描述:512K, 64K X 8, 2.5V SER EE,IND - Gel-pak, waffle pack, wafer, diced wafer on film
24LC512/W16K 制造商:Microchip Technology Inc 功能描述:512K, 64K X 8, 2.5V SER EE,IND,WAFER - Gel-pak, waffle pack, wafer, diced wafer on film
24LC512/WF16K 制造商:Microchip Technology Inc 功能描述:512K, 64K X 8, 2.5V SER EE,IND - Gel-pak, waffle pack, wafer, diced wafer on film
24LC512-E/MF 功能描述:電可擦除可編程只讀存儲器 64kx8 - 2.5V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
24LC512-E/MS 制造商:Microchip Technology Inc 功能描述:512K, 64K X 8, 2.5V SER EE, EXT - Rail/Tube 制造商:Microchip Technology Inc 功能描述:IC EEPROM 512KBIT 400KHZ 8MSOP 制造商:Microchip Technology Inc 功能描述:512K, 64K X 8, 2.5V SER EE, EXT, 8 MSOP 3x3mm TUBE