In order to run this program, edit the IP address and netmask in the
參數資料
型號： 20-101-0788
廠商： Rabbit Semiconductor
文件頁數： 51/90頁
文件大小： 0K
描述： COMPUTER SGL-BOARD OP6600 W/SRAM
標準包裝： 1
系列： SBC
模塊/板類型： 單板計算機模塊
適用于相關產品： OP6600
User’s Manual
51
5.5 Run the PINGME.C Demo
In order to run this program, edit the IP address and netmask in the PINGME.C program
(SAMPLES\TCPIP\ICMP) to the values given above (10.1.1.2 and 255.255.255.248).
Compile the program and start it running under Dynamic C. The crossover cable is con-
nected from your computer’s Ethernet adapter to the Intellicom board’s RJ-45 Ethernet
connector. When the program starts running, the green LNK light on the Intellicom board
should be on to indicate an Ethernet connection is made. (Note: If the LNK light does not
light, you may not have a crossover cable, or if you are using a hub perhaps the power is
off on the hub.)
The next step is to ping the board from your PC. This can be done by bringing up the MS-DOS
window and running the pingme program:
ping 10.1.1.2
or by Start > Run
and typing the entry
ping 10.1.1.2
Notice that the red ACT light flashes on the Intellicom board while the ping is taking
place, and indicates the transfer of data. The ping routine will ping the board four times
and write a summary message on the screen describing the operation.
5.6 Running More Demo Programs With a Direct Connection
The programs STATIC.C and SSI3.C (SAMPLES\TCPIP\HTTP) demonstrate how to
make the Intellicom board be a Web server. This program allows you to turn the LEDs on
an attached Demonstration Board from the Development Kit on and off from a remote
Web browser. In order to run these sample programs, edit the IP address as for the pingme
program, compile the program and start it executing. Then bring up your Web browser and
enter the following server address: http://10.1.1.2.
This should bring up the Web page served by the sample program.
The sample program RXSAMPLE.C (SAMPLES\TELNET) allows you to communicate with
the Intellicom board using the Telnet protocol. To run this program, edit the IP address,
compile the program, and start it running. Run the Telnet program on your PC (Start >
Run telnet 10.1.1.2
). Each character you type will be printed in Dynamic C's STDIO
window, indicating that the board is receiving the characters typed via TCP/IP.
相關PDF資料
PDF描述
20-101-1068 MODULE RABBITCORE RCM3315
20-101-1131 MODULE RCM4200 RABBITCORE
20-101-1139 RCM4310 RABBITCORE
20-101-1154 MODULE RCM4120 RABBITCORE
20-101-1197 MODULE RABBITCORE RCM3910 ROHS
相關代理商/技術參數
參數描述
201-0108-01 功能描述:印刷電路板和試驗板 RJ11/45 and USB Connector RoHS:否 制造商:3M Electronic Solutions Division 產品:Jumper & Insulated Wires 描述/功能:Jumper wire, 22 AWG 0.1 inch 長度:0.1 in 寬度:
20-101-0818 功能描述:單板計算機 BL2100 Fric Lk 512K RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm
20-101-0820 功能描述:COMPUTER SGL-BD BL2000 SRAM/FLSH RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器或微處理器模塊 系列:SBC 產品目錄繪圖:DLP-245SY-G 標準包裝:1 系列:USB 模塊/板類型:開發板 適用于相關產品:USB 其它名稱:813-1006
20-101-0841 功能描述:模塊化系統 - SOM BL2000 FRICT LOCK W/ RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-0847 功能描述:模塊化系統 - SOM BL2121 LOCK RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*