- 您現在的位置：買賣IC網 > PDF目錄368730 > 16F876 (Microchip Technology Inc.) CAT 5E CROSSOVER, GREEN 15 FT PATCH CABLE PDF資料下載
參數資料
| 型號： | 16F876 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | CAT 5E CROSSOVER, GREEN 15 FT PATCH CABLE |
| 中文描述： | 28/40-pin 8位CMOS閃存微控制器 |
| 文件頁數： | 126/200頁 |
| 文件大?。?/td> | 3544K |
| 代理商： | 16F876 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁當前第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁
PIC16F87X
DS30292B-page 126
1999 Microchip Technology Inc.
12.4
Power-On Reset (POR)
A Power-on Reset pulse is generated on-chip when
V
DD
rise is detected (in the range of 1.2V - 1.7V). To
take advantage of the POR, tie the MCLR pin directly
(or through a resistor) to V
DD
. This will eliminate exter-
nal RC components usually needed to create a Power-
on Reset. A maximum rise time for V
DD
is specified.
See Electrical Specifications for details.
When the device starts normal operation (exits the
reset condition), device operating parameters (voltage,
frequency, temperature,...) must be met to ensure oper-
ation. If these conditions are not met, the device must
be held in reset until the operating conditions are met.
Brown-out Reset may be used to meet the start-up con-
ditions. For additional information, refer to Application
Note,
AN007,
“Power-up
(DS00007).
Trouble
Shooting”,
12.5
Power-up Timer (PWRT)
The Power-up Timer provides a fixed 72 ms nominal
time-out on power-up only from the POR. The Power-
up Timer operates on an internal RC oscillator. The
chip is kept in reset as long as the PWRT is active. The
PWRT’s time delay allows V
DD
to rise to an acceptable
level. A configuration bit is provided to enable/disable
the PWRT.
The power-up time delay will vary from chip to chip due
to V
DD
, temperature and process variation. See DC
parameters for details (T
PWRT
, parameter #33).
12.6
Oscillator Start-up Timer (OST)
The Oscillator Start-up Timer (OST) provides 1024
oscillator cycle (from OSC1 input) delay after the
PWRT delay is over. This ensures that the crystal oscil-
lator or resonator has started and stabilized.
The OST time-out is invoked only for XT, LP and HS
modes and only on Power-on Reset or wake-up from
SLEEP.
12.7
Brown-Out Reset (BOR)
The configuration bit, BODEN, can enable or disable
the Brown-out Reset circuit. If V
DD
falls below V
BOR
(parameter D005, about 4V) for longer than T
BOR
(parameter #35, about 100
μ
S), the brown-out situa-
tion will reset the device. If V
DD
falls below V
BOR
for
less than T
BOR
, a reset may not occur.
Once the brown-out occurs, the device will remain in
brown-out reset until V
DD
rises above V
BOR
. The
power-up timer then keeps the device in reset for
T
PWRT
(parameter #33, about 72mS). If V
DD
should
fall below V
BOR
during T
PWRT
, the brown-out reset
process will restart when V
DD
rises above V
BOR
with
the power-up timer reset. The power-up timer is
always enabled when the brown-out reset circuit is
enabled regardless of the state of the PWRT configu-
ration bit.
12.8
Time-out Sequence
On power-up, the time-out sequence is as follows: The
PWRT delay starts (if enabled) when a POR reset
occurs. Then OST starts counting 1024 oscillator
cycles when PWRT ends (LP, XT, HS). When the OST
ends, the device comes out of RESET.
If MCLR is kept low long enough, the time-outs will
expire. Bringing MCLR high will begin execution imme-
diately. This is useful for testing purposes or to synchro-
nize more than one PIC16CXX device operating in
parallel.
Table 12-5 shows the reset conditions for the STATUS,
PCON and PC registers, while Table 12-6 shows the
reset conditions for all the registers.
12.9
Power Control/Status Register
(PCON)
The Power Control/Status Register, PCON, has up to
two bits depending upon the device.
Bit0 is Brown-out Reset Status bit, BOR. Bit BOR is
unknown on a Power-on Reset. It must then be set by
the user and checked on subsequent resets to see if bit
BOR cleared, indicating a BOR occurred. The BOR bit
is a "don’t care" bit and is not necessarily predictable if
the Brown-out Reset circuitry is disabled (by clearing
bit BODEN in the Configuration Word).
Bit1 is POR (Power-on Reset Status bit). It is cleared on
a Power-on Reset and unaffected otherwise. The user
must set this bit following a Power-on Reset.
相關PDF資料 |
PDF描述 |
|---|---|
| 16F877 | CAT 5E CROSSOVER PATCH CORD CABLE GREEN 20 FT |
| 16FL100S02 | 6A, 12A AND 16A FAST RECOVERY RECTIFIERS |
| 16FL100S05 | 6A, 12A AND 16A FAST RECOVERY RECTIFIERS |
| 16FL100S10 | 6A, 12A AND 16A FAST RECOVERY RECTIFIERS |
| 16FL10S02 | 6A, 12A AND 16A FAST RECOVERY RECTIFIERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 16F876A | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:28/40-pin Enhanced FLASH Microcontrollers |
| 16F877 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:28/40-pin 8-Bit CMOS FLASH Microcontrollers |
| 16F9040 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:COMPACT DIGITALMULTIMETER TRUE RMS |
| 16F9041 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:COMPACT DMM MIT RS232 |
| 16F946 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:中文資料 帶有LCD驅動器,采用鈉瓦技術的64引腳8位CMOS內存單片機 |
發布緊急采購，3分鐘左右您將得到回復。