- 您現在的位置：買賣IC網 > PDF目錄373840 > ZXBM2004 (Zetex Semiconductor) VARIABLE SPEED 2-PHASE BLDC MOTOR CONTROLLER PDF資料下載
參數資料
| 型號： | ZXBM2004 |
| 廠商： | Zetex Semiconductor |
| 英文描述： | VARIABLE SPEED 2-PHASE BLDC MOTOR CONTROLLER |
| 中文描述： | 變速2相無刷電機控制器 |
| 文件頁數： | 5/12頁 |
| 文件大小： | 249K |
| 代理商： | ZXBM2004 |
PIN FUNCTIONAL DESCRIPTION
H+ - Hall input
H- - Hall input
The rotorposition is detected by a Hall sensor, with the
outputappliedto theH+ andH-pins.This sensorcanbe
eithera 4pin 'naked' Hall device orofthe 3pin buffered
switching type. For a 4 pin device the differential Hall
output signal is connected to the H+ and H- pins. For a
buffered Hall sensor the Hall device output is attached
to the H+ pin, with a pull-up attached if needed, whilst
the H- pin has an external potential divider attached to
hold the pin at half V
. When H+ is high in relation to
H-, Ph2 is the active drive.
ThRef - Network Reference
This is a reference voltage of nominal 3V. Itis designed
for the ability to 'source' and therefore it will not 'sink'
any current from a higher voltage.
The currentdrawn from the pin by the minimum speed
potential divider to pin S
and any voltage setting
network should not exceed 1mA in total at maximum
temperature.
SPD - Speed Control Input
The voltage applied to the SPD pin provides control
over the Fan Motor speed by varying the Pulse Width
Modulated (PWM) drive ratio at the Ph1Lo and Ph2Lo
outputs. The control signal takes the form of a voltage
input of range 3V to 1V, representing 0% to 100% drive
respectively.
If variable speed control is not required this pin can be
left with an external potential divider to set a fixed
speed or tied to ground to provide full speed i.e. 100%
PWM drive.
If required this pin can also be used as an enable pin.
The application of a voltage >3.0V will force the PWM
drive fully off, in effect disabling the drive.
S
MIN
- Sets Minimum Speed
A voltage can be set on this pin via a potential divider
between the ThRef and Gnd. This voltage is monitored
by the SPD pin such that it cannot rise above it. As a
highervoltageontheSPD pinrepresents alowerspeed
it therefore restricts the lower speed range of the fan. If
this featureis notrequiredthepinis lefttiedto ThRefso
no minimum speed will be set.
If the fan is being controlled from an external voltage
source onto the SPD pin then either this feature should
not be used or if it is required then a >1k
should be placed in series with the SPD pin.
resistor
C
PWM
- Sets PWM Frequency
This pin has an external capacitor attached to set the
PWM frequency for the Phase drive outputs. A
capacitor value of 0.1nF will provide a PWM frequency
of typically 24kHz.
The C
timing period (T
PWM
) is determined by the
following equation:
T
V
(
V
x C
I
V
(
V
x C
I
PWM
THH
THL
PWMC
THH
THL
PWMD
=
+
)
)
Where:
C = C
PWM
+15, in pF
V
T HH
and V
T HL
are the C
PW M
pin
threshold voltages
I
PWMC
and I
PWMD
are the charge and
discharge currents in
T
PWM
is in ms
A.
ZXBM2004
S E M IC O N D U C T O R S
ISSUE 3 - MAY 2005
5
相關PDF資料 |
PDF描述 |
|---|---|
| ZXBM2004Q16TC | VARIABLE SPEED 2-PHASE BLDC MOTOR CONTROLLER |
| ZXCD1000 | HIGH FIDELITY CLASS D AUDIO AMPLIFIER SOLUTION |
| ZXCD1000EQ16 | HIGH FIDELITY CLASS D AUDIO AMPLIFIER SOLUTION |
| ZXCD1010 | HIGH FIDELITY CLASS D AUDIO AMPLIFIER SOLUTION |
| ZXCD1010EQ16 | HIGH FIDELITY CLASS D AUDIO AMPLIFIER SOLUTION |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ZXBM2004JA16TC | 功能描述:馬達/運動/點火控制器和驅動器 Motor Driver Ics RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| ZXBM2004N14TA | 功能描述:馬達/運動/點火控制器和驅動器 2-Phase DC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| ZXBM2004N14TC | 功能描述:馬達/運動/點火控制器和驅動器 2-Phase DC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| ZXBM2004Q16TA | 功能描述:馬達/運動/點火控制器和驅動器 2-Phase DC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| ZXBM2004Q16TC | 功能描述:馬達/運動/點火控制器和驅動器 2-Phase DC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。